What if every Indian train were coupled into one?

4.4 lakh wagons, coaches and locomotives make a 6,280 km train, about as long as the Earth's radius. It could move. Its brakes would need seven hours to reach the back.

Two diesel locomotives hauling a long freight train through Sitaphalmandi station, Secunderabad
Photo: Adityamadhav83, CC BY-SA 3.0, via Wikimedia Commons

If every Indian train were coupled into one, the 3.28 lakh wagons, 91,948 coaches and roughly 17,750 locomotives would make a train about 6,280 km long weighing around 2.5 crore tonnes, about as long as the Earth's radius and 1.5 times the country's longest rail route. Its own locomotives could pull it on level track, but a level crossing would stay shut for about six and a half days, and an air-brake command would take about seven hours to reach the last wagon.

Key takeaways
  • 4,37,689 vehicles: 3,27,991 wagons, 91,948 coaches and about 17,750 locomotives.
  • About 6,284 km long, 98.6% of the Earth's radius, and 2.48 crore tonnes.
  • About 940 WAG-12Bs could pull it at 50 km/h on level track; gradients raise that to thousands.
  • 7 hours for an air-brake signal at 250 m/s to reach the last wagon.
  • 6.5 days for it to pass a level crossing at 40.5 km/h.

Indian Railways has already been testing the idea in miniature, and the first trial is the best place to start.

The story

At 13:50 on 15 August 2022, as part of the Azadi Ka Amrit Mahotsav celebrations, South East Central Railway sent a freight train out of Korba in Chhattisgarh unlike any it had run before. Five coal rakes had been coupled into one: 295 loaded wagons, 3.5 km long, carrying more than 27,000 tonnes of coal, three times an ordinary rake's 9,000. It took about four minutes to clear a station. The train, named Super Vasuki, covered the 267 km to Rajnandgaon in 11 hours 20 minutes. Officials said its load could run a 3,000 MW power plant for a full day, and that longer trains would help keep coal moving in peak-demand seasons.

ThePrint: Railways conducts test run of its longest freight train carrying 27,000 tonnes of coal (August 2022)

In August 2025 East Central Railway went further with Rudrastra, a 4.5 km freight train with seven locomotives spread through it. This post scales that experiment to the whole fleet and checks what breaks first.

3,27,991freight wagons, March 2024 (IR Year Book)
91,948passenger coaches including EMUs, March 2024
6,280 kmlength of the coupled train, my estimate
7 hoursfor a brake signal to reach the last wagon

How long would one train of every Indian train be?

One train made of every Indian Railways vehicle would be about 6,280 km long, which is 98.6% of the Earth's radius of 6,371 km, and 9% of the network's 69,181 route kilometres. It would not fit on any single route in the country.

Counting the fleet

Counting the fleet first. Wikipedia's summary of the Indian Railways Year Book gives 3,27,991 freight wagons and 91,948 passenger coaches as of March 2024. Locomotive counts move every month as new electrics arrive and diesels retire; the same page lists 13,569 electric, 4,169 diesel and 16 steam locomotives in February 2026, which I round to 17,750.

Measuring each vehicle

Lengths next. Instead of guessing a wagon length, I use Super Vasuki itself:

  • Wagons: 3.5 km for 295 wagons and six locomotives is 11.6 m per vehicle, couplers included. Rudrastra gives a similar figure, about 12.8 m per vehicle for 4.5 km and roughly 350 vehicles (reports give 345 or 354 wagons).
  • Coaches: I assume 23 m (LHB coaches are about 24 m, older ICF coaches a little shorter).
  • Locomotives: 20 m for an average one. Both of these are my estimates.
VehicleCountLength eachTotal lengthMass each (estimate)Total mass
Freight wagons3,27,99111.6 m (from Super Vasuki)3,814 km55 t (half loaded)1.80 crore t
Passenger coaches91,94823 m2,115 km50 t46 lakh t
Locomotives17,75020 m355 km123 t22 lakh t
Total4,37,6896,284 km2.48 crore t

The mass column assumes half the wagons are loaded. Super Vasuki's gross load of 25,962 tonnes over 295 wagons gives 88 tonnes per loaded wagon, and an empty wagon weighs roughly a quarter of that, so 55 tonnes is a fleet average under my half-loaded assumption.

A brown Indian Railways BCNHL covered freight wagon on a siding
A BCNHL covered wagon, one of about 3.28 lakh freight wagons. Coupled end to end, the wagons alone would stretch roughly 3,800 km.Photo: Ravi Raj, CC BY-SA 4.0, via Wikimedia Commons
Length of the all-India train against real distances
See the data as a table
Length (km)
All-India train (estimate)6284
Earth's radius6371
Vivek Express route, Dibrugarh–Kanyakumari4155
Rudrastra freight train4.5
Super Vasuki freight train3.5

Source: IR Year Book fleet counts (via Wikipedia); Vivek Express route length; Super Vasuki and Rudrastra trial reports · All-India train length is my estimate from fleet counts and per-vehicle lengths.

The longest train route in India, the Dibrugarh–Kanyakumari Vivek Express, covers about 4,155 km. Our train is 1.5 times that, so even if you cleared the entire diagonal of the country it would not fit. It would have to be laid along several trunk routes joined through junctions, curling across the map like a very long snake.

Could the locomotives actually pull it?

Yes on level track, provided the locomotives are spread through the train. Rolling resistance for a freight train is about 2 to 3 newtons per kilonewton of weight, so 2.48 crore tonnes resist with about 609 meganewtons, and the fleet's own locomotives can supply that.

Train resistance is usually written with the Davis equation, \( R = A + Bv + Cv^{2} \):

  • A: a constant term from bearings and rolling;
  • Bv: a term growing with speed, from flange friction and oscillation;
  • Cv²: an aerodynamic term growing with speed squared.

Sawczuk and colleagues compared ten such models against a real coasting test in Poland. Working back from their model totals at 60 km/h for a 2,779-tonne train of loaded coal wagons gives roughly 1.8 to 3.2 N/kN. I use 2.5 N/kN.

  1. Weight. \( W = mg = 2.48\times10^{10}\ \text{kg} \times 9.81 = 2.43\times10^{11}\ \text{N} \).
  2. Resistance on level track. \( R = 0.0025 \times 2.43\times10^{11} = 6.09\times10^{8}\ \text{N} \), about 609 MN.
  3. Power at 50 km/h. \( P = Rv = 6.09\times10^{8} \times 13.9 = 8.5\times10^{9}\ \text{W} \), 8.5 GW.
  4. In WAG-12B units. Each WAG-12B is rated at 9,000 kW, so the train needs about 940 of them working flat out, against a fleet of about 17,750 locomotives of all types.
  5. Starting. A WAG-12B's starting tractive effort is 785 kN at 25 t axle load. On level track, each can start about \( 785{,}000 / (0.0025 \times 9.81) \approx 32{,}000 \) tonnes, so about 780 of them could get the whole train rolling.

Gradients change everything

A 1 in 100 climb adds 10 N/kN, five times the rolling resistance. At 12.5 N/kN in total, each WAG-12B can start only about 6,400 tonnes, so roughly 3,900 locomotives are needed, and since the train spans the country it will always be climbing somewhere.

That is why Rudrastra used distributed power, with one locomotive after every 59 wagons. Applied to all 3,27,991 wagons, that spacing needs about 5,560 locomotives, well within the fleet.

Distributed power, Rudrastra styleOne loco at the front: the first coupler carries the whole trainpeak coupler force hereA loco after every 59 wagons: each coupler carries one blockColoured blocks = locomotives. Grey dashes = wagons (not to scale).For all 3,27,991 wagons: about 5,560 locomotives at this spacing.
Spreading locomotives through the train is what made the 4.5 km Rudrastra possible. Coupler strength, not total horsepower, sets how long a train can be.
Determination of the resistance to motion of a cargo train when driving without a driveWojciech Sawczuk, Sławomir Kołodziejski, Armando Miguel Rilo Cañás · Combustion Engines 197(2) · 2024

The authors coasted a 468 m freight train of 35 loaded coal wagons and a diesel locomotive, 2,902.7 tonnes in all, from 60 km/h without traction, using the locomotive recorder to fit speed against time and distance. They compared ten resistance models used by European railways against the measured coast-down distance. Errors ranged from 2.4% to 63%; the Polish and the Czech–Slovak models were best at 2.4% and 8.5%. The limit: one train, one line, open coal wagons; resistance for covered wagons or passenger coaches differs.

Read the paper (free)
A WAG-12B electric locomotive hauling a freight train at Bharathnagar
A WAG-12B, rated at 9,000 kW. About 940 of them working flat out could move the all-India train at 50 km/h on level track.Photo: Adityamadhav83, CC BY-SA 4.0, via Wikimedia Commons

How long would the brakes take to work?

About seven hours. Railway air brakes are applied by dropping pressure in a pipe that runs the length of the train, and that pressure drop travels at a few hundred metres per second, so for 6,284 km it takes hours, not seconds, to reach the end.

In a conventional air brake, every wagon has a valve that applies its brakes when the brake-pipe pressure falls. The fall propagates as a pressure wave, physically a sound wave in compressed air slowed by pipe friction and valves.

European regulations, as cited by Crăciun and Mazilu, set a minimum braking-wave speed of 250 m/s:

\[ t_{brake} = \frac{L}{c_b} = \frac{6.284\times10^{6}\ \text{m}}{250\ \text{m/s}} = 25{,}100\ \text{s} \approx 7.0\ \text{h} \]

For the first seven hours, the front of the train would be braking while the back pushed on at full speed. In a normal train this delay is a second or two, and even that produces the jolts known as slack action as wagons run into each other.

Across 6,284 km, the compressive force would pile up until couplers or wagons failed. The only fix is to abandon the single brake pipe and send the brake command electronically, as electronically controlled pneumatic (ECP) brakes do, so that every wagon brakes at once.

The brake signal crawling down a 6,284 km train at 250 m/safter 1 hafter 3.5 hafter 7 h900 km braking; 5,384 km still pushing3,150 km brakingwhole train braking, at lastfrontrearColoured = brakes applied. In a normal 700 m train this takes about 3 seconds.
Distances are 250 m/s × time. The braked front and the unbraked rear meet at the couplers, which is where this train would fail.
Simulation of the longitudinal dynamic forces developed in the body of passenger trainsCamil Crăciun, Traian Mazilu · Annals of the Faculty of Engineering Hunedoara XII(3) · 2014

The Bucharest authors modelled each coach's buffers, draw gear and brake valves to compute the forces coaches exert on each other during braking. They assume a braking-wave speed of 250 m/s, the minimum allowed by the regulations they cite, and show how the delay means front coaches brake first while unbraked rear coaches run into them, producing large longitudinal forces. The limit: passenger trains of normal length; freight trains have more slack and slower brake build-up.

Read the paper (free)

How long would a level crossing stay shut?

At Rudrastra's trial average of 40.5 km/h, a 6,284 km train takes about 155 hours to pass a point, so a level crossing would stay shut for six and a half days. At 120 km/h, the WAG-12B's top speed, it would still be 52 hours.

\[ t_{LC} = \frac{L}{v} = \frac{6{,}284\ \text{km}}{40.5\ \text{km/h}} = 155\ \text{h} \approx 6.5\ \text{days} \]

Build your own all-India train

Indian Railways has 11,096 manned level crossings already interlocked with signals, according to a July 2025 reply in the Lok Sabha, and the ministry has been replacing crossings with road overbridges and underbridges for two decades.

Our train would turn every crossing it touches into a six-day roadblock. Every station would see the same train for six days, which also means no other train could use that line: the all-India train is, by construction, the only train.

The all-India train is, by construction, the only train.The working of this post
A freight train passing Boisar station on the Western Dedicated Freight Corridor
A freight train on the Western Dedicated Freight Corridor at Boisar. Separate freight lines exist so long, heavy trains stop blocking passenger traffic; the all-India train would block everything.Photo: Saankav, CC0, via Wikimedia Commons

How sensitive is the answer?

The length could move by about a tenth either way; none of the conclusions change. The brake delay stays in hours and the crossing closure in days under any plausible assumption.

ChangeEffect
Wagon length 12.8 m (Rudrastra) instead of 11.6 mLength 6,670 km; brake delay 7.4 h
Locomotive count 14,000 instead of 17,750Length 6,210 km
Brake signal at 290 m/s instead of 250 m/sBrake delay 6.0 h
All wagons loaded at 88 tMass rises to about 3.5 crore t; 8.5 GW becomes about 12 GW at 50 km/h
Speed 120 km/hLevel crossing shut for 52 h

The model's weakest link is that it treats the train as rigid. A real train is 4.4 lakh masses joined by springs and gaps, and Rudrastra's spacing of locomotives every 59 wagons exists precisely because coupler forces, not total power, set the practical limit on how long a train can be.

Verdict: impossible as one train

Indian Railways has enough locomotive power to move a 6,284 km, 2.48 crore tonne train on level ground, but the train cannot work. A 250 m/s brake wave needs about seven hours to reach the end, so the front stops while the back keeps coming, and the longitudinal forces would destroy couplers long before the rear brakes engaged. It is 1.5 times longer than the longest route and would block every crossing it meets for 6.5 days. With radio-linked distributed power and electronic brakes, the practical limit is trains of a few kilometres, which is exactly what Super Vasuki and Rudrastra are.

For how the network got its broad track, read why India runs on broad gauge and the history of Indian Railways since 1853. The punctuality data is in how late Indian trains really are, and the longest real services are ranked in India's longest train routes. Riders who move their bikes by rail can read the Ride Atlas guide to sending a motorcycle by train.

What if next?

Questions people ask

What is the longest train in India?

Among trial runs, East Central Railway's Rudrastra in August 2025 was about 4.5 km long with roughly 350 wagons and seven locomotives, longer than the 3.5 km Super Vasuki of 2022.

How many coaches and wagons does Indian Railways have?

The Indian Railways Year Book counted 3,27,991 freight wagons and 91,948 passenger coaches, including multiple-unit coaches, as of March 2024.

Which is the longest train route in India?

The Dibrugarh–Kanyakumari Vivek Express, at about 4,155 km and roughly 74 hours.

Why don't railways run much longer trains?

Coupler forces, brake delays and siding lengths. A brake command in an ordinary air brake travels at a few hundred metres per second, so very long trains need locomotives spread through them and, ideally, electronic braking.

Sources

  1. Wikipedia: Indian Railways (Indian Railways Year Book data). Source for wagon, coach and locomotive counts and route length.
  2. ThePrint: Railways conducts test run of its longest freight train carrying 27,000 tonnes of coal (2022). Source for the story: 15 August 2022, 13:50 from Korba, 295 wagons, 3.5 km, 27,000 t, 267 km in 11 h 20 min, and the 3,000 MW comparison.
  3. Zee News: Meet Super Vasuki, 3.5 km train with 6 locos and 295 wagons (2022). Source for six locomotives and 25,962 t gross weight.
  4. The Week (PTI): ECR conducts trial run of 4.5 km Rudrastra (2025). Source for Rudrastra length, locomotive spacing and 40.5 km/h.
  5. Wikipedia: Indian locomotive class WAG-12. Source for 9,000 kW and 785 kN.
  6. Wikipedia: Vivek Express. Source for the 4,155 km route.
  7. Sawczuk W. et al.: Resistance to motion of a cargo train, Combustion Engines (2024). Source for freight resistance of about 1.8–3.2 N/kN.
  8. Crăciun C., Mazilu T.: Longitudinal dynamic forces in passenger trains, Annals of the Faculty of Engineering Hunedoara (2014). Source for the 250 m/s braking wave.
  9. The Week (PTI): Three accidents at level crossings in 3.5 years (2025). Source for 11,096 interlocked level crossings.
Indian Railwaysrolling stockSuper VasukiRudrastratrain resistanceWAG-12Bair brakelevel crossing
Sapta

Sapta (Saptarshi Sarkar) is a mechanical engineer turned marketer in Bengaluru and a solo touring rider. He writes the seven Saptaverse blogs. Work with him or read more of Whyblog.

Keep reading in Whyblog

From the other blogs