What if your tyres were made of ice, steel or rasgulla?

Rubber is not an accident. Swap it for steel and your contact patch shrinks 50 times; swap it for ice and it melts at 23 mm an hour; swap it for rasgulla and it collapses at half the pressure your tyre runs at.

Rasgullas from Odisha and Bengal side by side, the Odisha ones creamier and the Bengali ones white
Photo: User:Utcursch, based on images from User:Psubhashish (Subhashish Panigrahi) and User:Pamri, CC BY-SA 3.0, via Wikimedia Commons

A steel tyre would roll with almost no resistance but grip roughly half as well as rubber, with a contact patch about 50 times smaller, so braking distances would double and the road would get dented. An ice tyre would crush itself on the asphalt's stones, melt at roughly 20 mm an hour on a 30°C day, and ride on a film of its own meltwater with grip close to zero. A rasgulla tyre would fail before you sat on it: market rasgullas yield at around 100 kPa, about half the 196 kPa an NS200's rear tyre runs at. Only rubber can drape over the road and grip.

Key takeaways
  • 70 cm²: the rear contact patch of a loaded NS200 at 28 psi; a steel hoop gets about 1.4 cm².
  • ~1% of a rubber footprint really touches the road; grip comes from hysteresis as rubber drapes over stone tips.
  • 17.7 m to stop from 60 km/h on rubber (μ 0.8), against about 142 m on ice or rasgulla (μ 0.1).
  • ~23 mm an hour: how fast an ice tread melts back on a 30°C day (estimate).
  • ~104 kPa: where a rasgulla gives way, about half the 196 kPa the tyre must hold.

The tyre is the most underrated part of a motorcycle. Every newton of acceleration, braking and cornering force passes through two patches of rubber about the size of a postcard each.

To show why that rubber matters, I swap it for three materials (one engineering, one frozen, one from a Kolkata sweet shop) and work out what each does under a real load: the rear wheel of a BS6 Pulsar NS200 with a rider.

0.79 gbest ABS stop measured on dry asphalt with rubber tyres (Huertas-Leyva et al., 2023)
~1%of a tyre's footprint actually touches the road (Persson et al., 2005)
81-144 Nhardness of six brands of market rasgulla (ICAR-NDRI, 2017)
~10 MPacompressive strength of freshwater ice (Gold, 1977)

What does a tyre actually have to do?

A tyre has three jobs, and they set the rules every replacement material is judged by:

  1. carry the load at a modest pressure;
  2. deform around the road's texture to create grip;
  3. survive millions of load cycles.

The tyre that started it all was a fix for hard wheels

Wheels ran on iron, wood and solid rubber for centuries before anyone filled one with air. The first practical air-filled tyre was a home experiment.

The story

In October 1887, John Boyd Dunlop, at his home in Belfast, built an air-filled tyre for his son's tricycle: an inflated tube of sheet rubber fitted to a wooden disc about 96 cm across. To test it, he rolled it across the yard alongside a metal tricycle wheel. The metal wheel stopped; the pneumatic one kept rolling until it hit a gatepost and bounced back. He fitted pneumatics to both rear wheels of the tricycle, then tried larger ones on a bicycle. His patent was granted on 7 December 1888, though it was later ruled invalid because Robert William Thomson had patented the idea in the 1840s. On 18 May 1889, Willie Hume rode Dunlop's tyres to victory in all four cycling events at the Queen's College Sports in Belfast.

Wikipedia: John Boyd Dunlop

Dunlop's yard test is the whole of this post in miniature: a hard wheel loses energy to every bump, an air-filled one carries the load and drapes over the ground.

The load and the pressure

Start with the load. The NS200 weighs 158 kg at kerb, per its owner's manual. Add a 75 kg rider (my assumption) and put 60% of the total on the rear (also an assumption, typical for a naked bike with a seated rider): the rear tyre carries about 140 kg, or 1,372 N.

The manual specifies 2 kgf/cm², about 196 kPa (28 psi), in the rear tyre for a solo rider. To a first approximation the contact patch area is load divided by pressure:

\[ A_{patch} \approx \frac{F}{p} = \frac{1{,}372\ \text{N}}{196{,}000\ \text{Pa}} = 0.0070\ \text{m}^2 = 70\ \text{cm}^2 \]

Seventy square centimetres, about the size of a credit card and a half. Now look closer. Persson and colleagues showed in 2005 that only about 1% of a tyre's nominal footprint is in real contact with the road, on the tips of the asphalt's stones.

The grip comes mostly from the rubber flexing over those tips and losing energy as it does, a property called hysteresis. That is the mechanism no other material on this list can copy.

Why rubber grips and steel slides (close-up)Rubbertread drapes over each stonesqueezed harder on the leading faceenergy lost each cycle = grip (μ ~0.8)sliding direction →Steelrigid: touches only the tipsno draping, no hysteresisdry sliding only (μ ~0.3–0.5, estimate)Not to scale. After Persson et al. (2005): real contact is about 1% of the footprint.
Grip on a road is mostly energy loss. Soft rubber deforms around each stone and resists being dragged over it; hard steel cannot.

How much grip does rubber give, in numbers?

Enough for a skilled rider to stop at about 0.8 g on dry asphalt. Huertas-Leyva and colleagues measured six experienced riders doing 85 emergency and planned stops from 35 to 45 km/h on a bike with ABS; the best rider, with the front ABS active 93.7% of the time, averaged 7.71 m/s², or 0.79 g.

ABS cycles at or just below the tyre's peak grip, so the tyre-road friction coefficient on that surface was at least about 0.79. I use μ = 0.8 for rubber below.

The friction coefficient \( \mu \) sets two limits every rider feels. The shortest stop from speed \( v \) and the deepest lean in a steady corner:

\[ d = \frac{v^2}{2 \mu g} \qquad \tan\theta_{max} = \mu \]

From 60 km/h (16.7 m/s) with \( \mu = 0.8 \): \( d = 16.7^2 / (2 \times 0.8 \times 9.81) = 17.7 \) m, and the maximum lean is \( \arctan(0.8) = 38.7^\circ \). Those are the benchmarks.

Calculated in this post from the friction coefficient of 0.8 taken from Huertas-Leyva et al. (2023) (their best measured stop was 0.79 g).

Wet asphalt lowers them: the same Persson study found rubber friction on wet rough surfaces at low speed is 20 to 30% lower than dry, because water trapped in the road's pits seals them off from the rubber.

What if your tyres were made of steel?

A steel tyre would carry the load easily and roll beautifully, but its contact patch would be tiny and its grip on asphalt poor. Railways accept that trade because a train runs on smooth steel rails, needs low rolling resistance more than grip, and never has to lean into a corner.

The contact patch of a rigid cylinder on a flat surface comes from Hertz contact theory. For a steel hoop of radius \( R = 0.307 \) m (the NS200's 130/70-17 tyre is about 614 mm across) and a flat tread of width \( L = 50 \) mm pressed onto asphalt:

  1. Effective modulus. Steel (about 200 GPa) is so much stiffer than asphalt that the asphalt does nearly all the deforming. I take asphalt at about 5 GPa with a Poisson ratio of 0.35 (an estimate; asphalt stiffness varies widely with temperature):
    \[ E^* \approx \frac{E_{asphalt}}{1-\nu^2} = \frac{5\ \text{GPa}}{0.88} \approx 5.7\ \text{GPa} \]
  2. Contact half-width.
    \[ a = \sqrt{\frac{4 F R}{\pi L E^*}} = \sqrt{\frac{4 \times 1372 \times 0.307}{\pi \times 0.05 \times 5.7\times10^{9}}} \approx 1.4\ \text{mm} \]
  3. Patch area and peak pressure. The patch is about 2.7 mm by 50 mm, or 1.4 cm², against 70 cm² for rubber, a factor of 50. Peak pressure is:
    \[ p_{max} = \frac{2F}{\pi a L} = \frac{2 \times 1372}{\pi \times 0.0014 \times 0.05} \approx 12.7\ \text{MPa} \]
    That is 65 times the pressure of an air-filled tyre, concentrated on the stone tips. On a hot afternoon, when asphalt softens, a steel tyre would leave a groove.

    Calculated in this post from the 1,372 N rear load (the NS200 owner's manual kerb weight, plus my assumed rider and weight split), the 196 kPa rear tyre pressure from the same manual, and Hertz contact theory with my estimate of asphalt stiffness. With these example inputs (a 75 kg rider and 60% of the load on the rear), this is not a measured figure.

Steel's real problem is grip

Grip is the bigger problem. Steel cannot flex over the stones, so the hysteresis part of friction disappears and only dry sliding friction of steel on stone remains.

I estimate \( \mu \) at 0.3 to 0.5 on clean dry asphalt (my estimate; I could not find a measured value for steel on road asphalt), which doubles braking distance and halves cornering lean. Any contamination makes it far worse: on railways, wet leaves on the rail cut wheel-rail friction to below 0.1, according to Ishizaka and colleagues' 2017 review in Wear.

An old wooden cart wheel with an iron or steel band around its rim
A 19th-century cart wheel with a steel tyre shrunk onto its wooden rim. It worked at walking pace; at motorcycle speeds the small, hard contact patch is the problem.Photo: denisbin from Adelaide, Australia, CC0, via Wikimedia Commons

What if your tyres were made of ice?

An ice tyre fails three ways at once: it crushes, it melts, and it slides on its own meltwater. Ice is stiff and fairly strong in slow compression, but it is brittle and it sits 30 degrees below an Indian afternoon.

Crushing

Gold's 1977 review of freshwater ice in the Journal of Glaciology gives a Young's modulus of about 7 GPa and an unconfined compressive strength of about 10 MPa at a strain rate of 10⁻³ per second, with uniaxial tensile strength of only 1 to 2 MPa.

Run the same Hertz calculation for a 130 mm-wide ice cylinder on asphalt (combined modulus about 3.3 GPa) and the average peak pressure is about 6 MPa. That sounds safe until you remember that only the stone tips touch, so local stresses are many times higher. The tread would grind away into ice dust, and the first pothole edge would load it in tension, where ice is weakest.

Melting

The tyre is an annulus from the 17-inch rim (radius 0.216 m) to 0.307 m, 0.13 m wide:

Calculated in this post from the 130/70-17 rear tyre size in the NS200 owner's manual.

\[ V = \pi (0.307^2 - 0.216^2) \times 0.13 \approx 0.0195\ \text{m}^3 \;\Rightarrow\; m \approx 917 \times 0.0195 \approx 17.8\ \text{kg} \]

Using standard values for ice (density 917 kg/m³, latent heat of fusion 334 kJ/kg), melting it from 0°C takes about 5.9 MJ (\( 17.8 \times 334 \)). The heat comes in three ways:

  • forced convection from 30°C air: an estimated 45 W/m²K at riding speed over the tyre's roughly 0.55 m² of surface and a 30 K difference;
  • conduction from the road;
  • sunshine, which with the road adds a few hundred watts.

The input is about 1 kW. Concentrating on the tread alone, about 2 kW/m² reaches it, so it melts back at:

\[ \dot{s} = \frac{q''}{\rho L_f} = \frac{2{,}000}{917 \times 334{,}000} \approx 6.5\times10^{-6}\ \text{m/s} \approx 23\ \text{mm/hour} \]

So the tread loses a couple of centimetres an hour and the whole tyre is gone in a couple of hours, all of it estimates with the working shown.

Grip

Meltwater at 0°C lubricates the contact. I estimate \( \mu \approx 0.1 \), similar to what icy surfaces give in winter, which means a stop from 60 km/h takes about 142 m and the bike cannot lean beyond about 6 degrees.

A large block of ice melting on a riverbank in spring
A block of river ice melting in spring sunshine in Finland. An ice tyre on a 30°C Indian road would lose its tread at roughly 23 mm an hour by the estimate above, before counting the grinding.Photo: SeppVei, Public domain, via Wikimedia Commons

What if your tyres were made of rasgulla?

A rasgulla tyre collapses under its own job, because chhena soaked in syrup yields at roughly half the pressure a tyre must carry. This is the one material on the list that has been properly tested in a lab, by dairy scientists rather than tyre engineers.

Srinivasa, Barnwal and Singh at ICAR's National Dairy Research Institute in Karnal measured six brands of market rasogolla in 2017. Unit weights ran from 15.7 to 43.4 g, and texture-profile hardness (the peak force in the first compression) ran from 81.3 to 144.3 N, with springiness from 0.44 to 0.92.

Treat a rasgulla as a sphere about 35 mm across (my estimate for a typical one) and the peak compressive stress is roughly:

\[ \sigma \approx \frac{F}{\pi r^2} = \frac{100\ \text{N}}{\pi \times 0.0175^2} \approx 104\ \text{kPa} \]
  1. Required patch. If the material gives way at about 104 kPa, the patch must grow until pressure falls to that level:
    \[ A = \frac{1{,}372}{104{,}000} \approx 132\ \text{cm}^2 \]
    That is nearly twice the 70 cm² of the real tyre, and the material only gets there by being squashed by half, which is what the texture test does.
  2. Recovery. Springiness of 0.44 to 0.92 (ICAR-NDRI, 2017) means a rasgulla recovers between 44% and 92% of its height after a compression. The rear wheel turns about 8.6 times a second at 60 km/h (614 mm diameter), so the tread is crushed and released about 520 times a minute. Each cycle squeezes out syrup and leaves the chhena a little flatter.
  3. How many sweets. At a soaked density of about 1,100 kg/m³ (my estimate), the 0.0195 m³ tyre weighs about 21 kg, or roughly 600 rasgullas of 35 g each.

The grip is the final insult. The contact is lubricated by sugar syrup, so friction would be low (I estimate 0.1 to 0.2), and the syrup would coat the road for everyone behind you. The 2017 study also found hardness and springiness differ strongly by brand (p < 0.001), so the rasgulla you choose matters, but not enough to matter.

White rasgullas in sugar syrup
Rasgullas in syrup. Lab texture tests put their hardness at 81 to 144 N, roughly 100 kPa for one sweet, about half the pressure inside a motorcycle's rear tyre.Photo: HrichikHv, CC BY-SA 4.0, via Wikimedia Commons

How do the four materials compare side by side?

Tyre materialFriction coefficient on asphaltContact patch (rear, 1,372 N)Stop from 60 km/hMaximum leanWhat kills it
Rubber (air-filled)0.8 (measured lower bound 0.79)about 70 cm²17.7 m38.7°Wear over 15,000 to 30,000 km
Steel hoop0.3 to 0.5 (estimate)about 1.4 cm²28 to 47 m17° to 27°Poor grip; dents the road; no cushioning
Iceabout 0.1 (estimate, wet film)small, then crushingabout 142 mabout 6°Melts at about 23 mm/h; brittle in tension
Rasgulla0.1 to 0.2 (estimate, syrup film)132 cm² at 50% squash71 to 142 m6° to 11°Yields at about 104 kPa, below tyre pressure
Rear contact patch under 1,372 N, same scaleRubber~70 cm² at 196 kPaSteel~1.4 cm²2.7 × 50 mmRasgulla~132 cm², squashed by halfScale: 20 px per cm. Areas from this post's worked estimates.
Steel's patch is a sliver, a fiftieth of rubber's. Rasgulla's is huge, but only because it has already been crushed to half its height.

The rubber wear figure is a common service range rather than a sourced number, so treat it as indicative. For how to read where your own rubber is in that life, see how to check tyre wear and age.

Stopping distance from 60 km/h by tyre material
See the data as a table
Stopping distance (m)
Rubber (μ 0.8)17.7
Steel, best case (μ 0.5)28.3
Steel, worst case (μ 0.3)47.2
Rasgulla, best case (μ 0.2)70.8
Ice or rasgulla (μ 0.1)141.6

Source: Calculated as d = v²/(2μg); rubber μ from Huertas-Leyva et al. (2023), others are estimates stated in the post · Braking distance only, excluding reaction time.

What your tyre friction allows

Is any version of these tyres actually possible?

Steel is possible with changes, ice and rasgulla are not. Here is the case for each, built from the numbers above.

  • Steel: It carries the load, lasts, and rolls easily; it fails on grip and comfort. The fix is to wrap the steel hoop in a thick rubber tread, at which point you have reinvented the solid tyre, and then add air for comfort and contact area, at which point you have reinvented the pneumatic tyre. Airless designs using resin spokes and a rubber tread are the modern middle path, and they are still limited to low speeds.
  • Ice: Its strength is fine in theory but its melting point is 0°C and Indian roads run far hotter. Even in a freezer-cold world it would crush on asphalt stones and slip on its meltwater film. Impossible on a road bike.
  • Rasgulla: It yields at about 104 kPa, and the tyre needs at least 196 kPa. Doubling the width only helps until the sidewall, also rasgulla, folds. Impossible.
Verdict: ice and rasgulla impossible, steel only with rubber added

A rasgulla tyre yields at roughly 104 kPa against a required 196 kPa, so it fails before the bike moves; an ice tyre melts back about 23 mm an hour on a 30°C day and grips at roughly μ 0.1, giving a 142 m stop from 60 km/h. Steel carries the load but has a contact patch 50 times smaller and, by my estimate, half the grip, so it only works once you add a rubber tread. The deciding law is the physics of rubber friction: grip comes from hysteresis as the tread drapes over the road's texture, and only a soft, elastic, energy-absorbing material can do that.

How sensitive are these results to the assumptions?

The rankings do not change; the exact numbers do.

Assumption movedWhat changes
Rear carries 50% instead of 60%Every contact patch shrinks by a sixth
Soft asphalt, 1 GPa instead of 5 GPaSteel patch grows about 2.2 times; peak pressure falls to about 5.7 MPa, still a groove-maker
Ice tyre at night in 20°C airConvection drops by a third; melt rate to about 16 mm an hour
Hardest rasgulla brand (144 N)Yield stress about 150 kPa, still below 196 kPa

The 0.8 rubber figure is itself conservative: tyre-road friction on good dry asphalt can exceed it, which only widens the gap.

Grip comes from a material that drapes over the road and loses energy doing it. Steel will not drape, ice melts, and rasgulla does not come back.

For more on what is happening inside the real thing, read what tyre size markings mean, whether nitrogen in tyres helps, and how ABS keeps a tyre at peak grip. The tyre-road physics also connects to the cornering ABS and traction control post, and the rest of the engineering is on the Yantra page.

What does the research say?

Rubber friction on wet and dry road surfaces: the sealing effectB. N. J. Persson, U. Tartaglino, O. Albohr, E. Tosatti · Physical Review B 71, 035428 · 2005

A theory paper on why rubber grips roads. Friction comes mainly from viscoelastic energy loss as the rubber deforms over road asperities across many length scales; the real contact area of a tyre is typically only about 1% of its nominal footprint. The authors show that at low sliding speed friction on wet rough surfaces is 20 to 30% lower than dry, and argue this is because rubber seals water into the surface's cavities, smoothing the road it can feel, rather than because of hydrodynamic lift. Limit: theory checked against lab data, not full-tyre road tests.

Read the paper (free)
Selected Physical, Colour and Textural Characteristics of Market RasogollaSrinivasa K., Pradyuman Barnwal, Pritpal Singh · Indian Journal of Dairy Science 70(2) · 2017

Researchers at ICAR-National Dairy Research Institute, Karnal, measured six brands of market rasogolla for size, unit weight, juiciness, porosity, colour and texture-profile parameters. Unit weight ranged from 15.7 to 43.4 g; hardness from 81.3 to 144.3 N; springiness from 0.44 to 0.92. Cohesiveness, hardness, springiness, gumminess and chewiness all differed significantly by brand (p < 0.001). Limit: texture tests compress single pieces at lab speeds, far gentler than a rolling tyre.

Read the paper (free)
Does ABS ensure good performance in emergency braking for less skilled motorcyclists?Pedro Huertas-Leyva, Giovanni Savino, Niccolò Baldanzini, Marco Pierini · Accident Analysis and Prevention 190 · 2023

Six experienced riders performed 85 full stops from 35 to 45 km/h: emergency stops in an intersection mock-up with a surprise car, and planned hard stops. The best rider used front ABS for 93.7% of braking and averaged 7.71 m/s²; the worst used it far less and managed 5.2 m/s². Best results came with front ABS active over 80% of braking time. Limit: only six riders, one bike and dry pavement.

Read the paper

What if next?

Questions people ask

Why are tyres made of rubber and not steel?

Because grip on a road comes mostly from the tread deforming over the road's texture and losing energy as it does. Steel cannot deform enough, so its contact patch is about 50 times smaller and its grip far lower. Trains can use steel because they run on smooth steel rails and need low rolling resistance more than grip.

Would a steel tyre ever puncture or wear out?

It would not puncture, and it would wear very slowly, but it would wear the road instead. Peak contact pressure under a steel motorcycle wheel works out to about 12.7 MPa, 65 times that of an air-filled tyre, enough to groove asphalt that has softened in the sun.

Calculated in this post from the 1,372 N rear load (NS200 owner's manual, plus my assumed rider and weight split) and Hertz contact theory, as worked above. With these example inputs (a 75 kg rider and 60% of the load on the rear), it is not a measured figure.

Could ice tyres work in very cold places?

Not on asphalt. Even below freezing, ice is brittle in tension, with a tensile strength of only 1 to 2 MPa, and the stone tips of asphalt concentrate stress far above its roughly 10 MPa compressive strength. Vehicles in cold places use rubber with studs or special compounds instead.

How much force can a rasgulla take before it breaks?

Market rasgullas in a 2017 ICAR-NDRI study needed 81 to 144 N to compress in a texture test, depending on the brand. For a sweet about 35 mm across, that is roughly 100 kPa, about half the pressure inside a motorcycle's rear tyre.

Sources

  1. Bajaj Auto: Pulsar NS200 BS VI owner's manual (source for the 158 kg kerb weight, 130/70-17 rear tyre and 28 psi rear pressure)
  2. Persson, B. N. J. et al.: Rubber friction on wet and dry road surfaces: the sealing effect, Physical Review B (2005) (source for the 1% real contact area and 20 to 30% wet reduction)
  3. Huertas-Leyva, P. et al.: Does ABS ensure good performance in emergency braking for less skilled motorcyclists? Accident Analysis and Prevention (2023) (source for the 7.71 m/s² best stop)
  4. Srinivasa K. et al.: Selected physical, colour and textural characteristics of market rasogolla, Indian Journal of Dairy Science (2017) (source for rasgulla hardness, springiness and unit weight)
  5. Gold, L. W.: Engineering properties of fresh-water ice, Journal of Glaciology (1977) (source for the 10 MPa compressive strength, 1 to 2 MPa tensile strength and 7 GPa modulus)
  6. Ishizaka, K., Lewis, S. R. and Lewis, R.: The low adhesion problem due to leaf contamination in the wheel/rail contact, Wear (2017) (source for wheel-rail friction below 0.1 with wet leaves)
  7. AutoPapo: Bridgestone AirFree in commercial service (2026)
  8. Tyre News: Puncture-free tyres edge closer as Bridgestone and Michelin scale up trials (2025)
  9. Wikipedia: John Boyd Dunlop (source for the October 1887 tricycle tyre, the yard test, the 7 December 1888 patent, Thomson's earlier patent and Willie Hume's 18 May 1889 wins)
tyre frictioncontact patchHertz contactrubber hysteresisicerasgullabraking distancewhat if
Sapta

Sapta (Saptarshi Sarkar) is a mechanical engineer turned marketer in Bengaluru and a solo touring rider. He writes the seven Saptaverse blogs. Work with him or read more of RoadHook Machines.

Keep reading in RoadHook Machines

From the other blogs