A motorcycle with 100 gears would keep its engine within about 1% of the ideal speed at all times, yet in my simulation of a 200 cc bike it reaches 100 km/h in 12.7 to 31.4 s against 8.2 to 9.1 s for six gears, because 99 gear changes each cut drive for a moment. For a petrol engine with a narrow power band, five to eight ratios is the real optimum; six is where most bikes land.
- With the same spread, 100 gears shrink the step between ratios from 1.253 to 1.0115.
- That recovers at most about 9% of average power, and about 3% of 0-100 time with instant shifts.
- With real shifts, 100 gears take 12.7 to 31.4 s to 100 km/h against 8.2 to 9.1 s for six.
- One gear: 43 km/h flat out in first, or about 75 km/h of clutch slip in sixth.
- For a manual petrol bike, five to eight ratios is the optimum.
Even with instant shifts, 100 gears are only about 3% quicker than a 10-speed. With a single gear, the bike either tops out at about 43 km/h (first gear) or takes 16.6 s to reach 100 km/h while its clutch slips for most of that time (sixth gear).
Gears exist because a petrol engine is a fussy power source. It makes useful power only over a band of rpm, roughly from peak torque to just past peak power, while the bike has to go from standstill to 130 km/h.
The gearbox is a set of fixed levers that keep the engine inside its band. So the question "how many gears?" is really "how much does staying in the band help, and what does each extra lever cost?" I answer it with a real gearbox, a real power curve and a simple simulation.
Why does a motorcycle need gears at all?
Because a piston engine makes power over a narrow rpm range, and the wheel needs force over a wide speed range. A spark-ignition engine simply does not have enough rpm range to cover everything from standstill to top speed in one ratio. The ideal, called the tractive-force hyperbola, is the force you would get if the engine ran at peak power at every road speed:
A real gearbox approximates that curve with a series of fixed ratios. Each gear gives a force curve shaped like the engine's torque curve, scaled by the overall reduction:
where \( T_e \) is engine torque, \( i_p \), \( i_g \), \( i_f \) are the primary, gearbox and final ratios, \( \eta \) is drivetrain efficiency (I use 0.9) and \( r_w \) is the rolling radius. The gaps between the gear curves and the hyperbola are lost acceleration.
What does a real six-speed look like?
The KTM 200 Duke, from the same KTM-Bajaj engine family as many Indian 200s, has a well-published gearbox: primary drive 72:22 (3.27), gears 12:34 (2.833), 15:31 (2.067), 18:28 (1.556), 21:26 (1.238), 22:23 (1.045) and 24:22 (0.917), and a 14:43 final drive (3.07), with 19 kW at 10,000 rpm and 20 Nm at 6,800 rpm. Two numbers describe any gearbox:
- Spread, the ratio of first gear to top gear:\[ \text{spread} = \frac{i_1}{i_N} = \frac{2.833}{0.917} = 3.09 \]
- Mean step, the geometric average jump between neighbouring gears:\[ \varphi = \text{spread}^{1/(N-1)} = 3.09^{1/5} = 1.253 \]Each upshift drops engine rpm by about 20%.
- With 100 gears and the same spread, the step shrinks to \( 3.09^{1/99} = 1.0115 \): each upshift drops rpm by only 1.1%.
Calculated in this post from the KTM 200 Duke's first and sixth gear ratios (2.833 and 0.917, moto-data.net).
Suzuki once built the gearbox this post imagines, or a good part of it. Its 50 cc Grand Prix twin, the RK66 (CycleChaos), had a 49.7 cc water-cooled two-stroke engine that made about 18 hp at 18,000 rpm, and a power band so narrow that Suzuki gave it a fourteen-speed gearbox. It was good for over 110 mph (about 177 km/h).
Hans Georg Anscheidt won the 1966 50 cc world championship on a Suzuki 50, and the factory dominated 1967 (CycleChaos). Then the rule-makers stepped in. New regulations for the 1969 season allowed 50 cc machines only one cylinder and six gears, and that ended the twin's career. The lesson of the RK66 is the lesson of this post: the narrower the engine's band, the more gears it can use, and someone eventually decides six is enough.
CycleChaos: Suzuki RM50 and RK66In first gear the overall reduction is \( 3.27 \times 2.833 \times 3.07 = 28.5 \), so every newton-metre at the crank becomes about 28 at the axle, as the sprocket gearing calculator shows in more detail.

How much power does a six-speed leave on the table?
On average about 10% during full-throttle acceleration, by a simple model. Suppose torque is roughly flat near the top of the rev range, so power is proportional to rpm. Shift at peak power and the engine drops to \( 1/\varphi \) of that rpm, and therefore to about \( 1/\varphi \) of peak power:
For six gears, \( 1/1.253 = 0.80 \) and the average is about 0.90. For 100 gears, \( 1/1.0115 = 0.989 \) and the average is about 0.994. So 100 gears could recover at most about 9% of average power during acceleration, before counting any cost. That is the whole prize.
What does each gear change cost?
A gear change interrupts drive: the clutch opens (or the quickshifter cuts ignition), the gears swap, and drive resumes. For a manual shift I assume about 0.25 s of no thrust, and for a good quickshifter about 0.05 s (both my estimates).
Every interruption costs speed, because drag and rolling resistance keep working while the engine is disconnected. With a fixed spread, the number of shifts to reach a given speed rises almost in proportion to the number of gears.
The simulation
To see the net effect I simulated a 233 kg bike plus rider (an NS200's 158 kg kerb weight plus 75 kg) with the 200 Duke's ratios and power figures, from standstill to 100 km/h. The model integrates \( m\, dv/dt = F - \tfrac{1}{2}\rho C_dA v^2 - C_{rr} m g \) in 2 ms steps, with these assumptions:
- \( C_dA = 0.5 \) m² (upright rider, Warwick wind-tunnel range) and \( C_{rr} = 0.015 \) (estimate);
- a torque curve passing through the published 20 Nm at 6,800 rpm and 18.1 Nm at 10,000 rpm (other points estimated);
- a clutch launch at 6,000 rpm, a 0.9g traction limit and upshifts at 10,500 rpm;
- ratios spaced geometrically between 2.833 and 0.917.
| Gears | Step between gears | 0-100 km/h, instant shifts | 0-100 km/h, 0.05 s shifts | 0-100 km/h, 0.25 s shifts |
|---|---|---|---|---|
| 1 (first only) | n/a | never (tops out at 42.6 km/h) | never | never |
| 1 (sixth only, clutch slip) | n/a | 16.6 s | 16.6 s | 16.6 s |
| 2 | 3.09 | 12.4 s | 12.4 s | 12.7 s |
| 4 | 1.46 | 8.6 s | 8.8 s | 9.6 s |
| 6 | 1.25 | 7.9 s | 8.2 s | 9.1 s |
| 10 | 1.13 | 7.7 s | 8.2 s | 9.8 s |
| 20 | 1.061 | 7.7 s | 8.7 s | 12.4 s |
| 50 | 1.023 | 8.0 s | 10.3 s | 19.8 s |
| 100 | 1.0115 | 8.0 s | 12.7 s | 31.4 s |
See the data as a table
| Instant shifts (s) | 0.05 s quickshifter (s) | 0.25 s manual shift (s) | |
|---|---|---|---|
| 2 | 12.38 | 12.44 | 12.68 |
| 3 | 9.73 | 9.86 | 10.38 |
| 4 | 8.64 | 8.83 | 9.63 |
| 5 | 8.05 | 8.33 | 9.43 |
| 6 | 7.93 | 8.17 | 9.13 |
| 8 | 7.83 | 8.21 | 9.72 |
| 10 | 7.72 | 8.15 | 9.84 |
| 20 | 7.74 | 8.66 | 12.36 |
| 50 | 7.96 | 10.34 | 19.81 |
| 100 | 8.04 | 12.73 | 31.38 |
Source: My simulation using KTM 200 Duke gearing and power data (moto-data.net) and NS200 kerb weight (Bajaj manual) · Shift times and parts of the torque curve are estimates; top speed is about 130 km/h in every case with 2 or more gears.
What the numbers say
- Instant shifts: the curve is almost flat from 6 gears on. Going from 6 to 10 gains 0.2 s, about 3%, and going to 100 gains nothing, because the engine spends its time near the falling top of its torque curve.
Calculated in this post from the simulation table above (7.93 s with six gears, 7.72 s with ten), built on the KTM 200 Duke's published gearing and power (moto-data.net) and the NS200 kerb weight (Bajaj owner's manual).
- Quickshifter: the best is 6 to 10 gears.
- Manual shifts: the best is 6.
With 100 gears and manual shifting, the bike takes almost four times as long as a six-speed, because it spends about 25 of its 31 seconds in neutral-like gaps.
What happens with only one gear?
You must choose between top speed and getting moving. Each is bad in its own way.
- Only first gear (overall 28.5). At 10,500 rpm the bike is doing about 43 km/h, and the simulation tops out at 42.6 km/h. Great for climbing a ghat road, useless on a highway.
Calculated in this post from the 200 Duke's first-gear overall ratio of 28.5 (ratios from moto-data.net) at 10,500 rpm, with an assumed rolling radius of about 0.31 m, with these example inputs.
- Only sixth gear (overall 9.2). Top speed is unchanged at about 130 km/h, but at the 6,000 rpm launch speed the bike is already doing about 75 km/h if the clutch were locked. Below that the clutch must slip. The simulation reaches 100 km/h in 16.6 s, about twice the six-speed time, with the clutch slipping for most of the first 75 km/h.
Calculated in this post from the sixth-gear overall ratio of 9.2 (3.27 x 0.917 x 3.07, ratios from moto-data.net) at 6,000 rpm, with an assumed rolling radius of about 0.31 m, with these example inputs.
That slipping is where the energy goes. While the clutch slips, the engine makes power at 6,000 rpm but the wheel uses only the part that matches road speed; the rest becomes heat in the clutch plates.
By my estimate, the engine makes about 10.9 kW at 6,000 rpm for the roughly 11.6 s it takes to reach 75 km/h, about 127 kJ, of which only about 50 kJ ends up as the bike's kinetic energy; most of the remaining 70 kJ or so becomes heat in the clutch plates on every launch, enough to glaze a small wet clutch after a few repeats. For how a clutch handles heat, see how a motorcycle clutch works.

Then why do scooters and electric bikes manage with one gear?
Because they change the problem, not the physics. A scooter's CVT is not one gear but infinitely many: belt pulleys change diameter continuously, with no shift interruption, at the cost of belt losses. An electric motor makes high torque from zero rpm and useful power across a wide speed range, so a single fixed reduction covers most needs.
Even electric vehicles gain from a second ratio, though. Spanoudakis and colleagues at the Technical University of Crete built a test vehicle and compared a single-stage transmission, a custom two-speed gearbox and a custom CVT on the road. The two-speed cut energy consumption by up to 3.8%, depending heavily on when it shifted, and the CVT by 4.3% in a single lap test. In India, the Matter AERA launched as a geared electric motorcycle with a four-speed manual gearbox and an 11.5 kW motor, according to a March 2026 report.
Design your own gearbox
Why does 100 gears also cost efficiency, not just time?
Because every gear pair in the box spins in oil whether it carries power or not. In a constant-mesh gearbox all the gear pairs are always meshed; only the selected one is locked to its shaft.
Anderson and Loewenthal's 1980 NASA analysis of spur gear systems found mesh efficiency generally above 98% except at very low torque, but also that no-load (tare) losses from windage and churning are a significant share of total loss except at low speed.
A 100-speed box would have 100 gear pairs churning oil, and its shafts would be long enough to need extra bearings, each with its own drag. The power path would still pass through one mesh, but the spinning losses would grow with every pair you add. Rough estimate: if each idle pair cost even 0.1% of power, 100 of them would cost 10%, more than the 9% the extra ratios can recover.
A 100-speed gearbox would need a shaft about as long as the bike, and the rider would click 99 times to reach top gear.
Then there is size. A motorcycle gearbox lives inside the engine cases. Each pair needs perhaps 15 to 20 mm of shaft length (my estimate for small-bike gears and selectors), so 100 pairs would need a shaft about 1.5 to 2 m long, as long as the bike. The selector drum would need 100 positions and the rider 99 clicks to reach top gear.
What does the research on gear count say?
Car and EV research agrees that extra gears pay off weakly and then not at all. The US EPA's ALPHA vehicle model, used for greenhouse-gas rule-making, found that:
- no single ratio progression is best for every engine;
- fuel use is relatively insensitive to progression;
- passing times, such as 30-50 and 50-70 mph, are highly sensitive to ratios and shift calibration.
Cars can use more ratios than bikes because automatic gearboxes shift under load with overlapping clutches, while a motorcycle's dog-ring gearbox interrupts drive on every shift.
Using EPA's physics-based ALPHA full-vehicle simulation, the authors varied ratio progression in six- and eight-speed automatics paired with four engines, from a 2010-era dual-cam-phased engine to a hypothetical 24 bar boosted engine, and swept final drive ratio. No single progression minimised carbon emissions for all combinations, and emissions were fairly insensitive to progression; final drive ratio mattered more. Passing times were highly sensitive to ratios and shift calibration. Limit: light-duty cars with automatics, not motorcycles with manual gearboxes.
Read the paper (free)The authors built and road-tested a single-stage transmission, a prototype two-speed gearbox and an electronically controlled CVT on a hydrogen fuel-cell urban test vehicle. The two-speed reduced overall energy consumption by up to 3.8%, with the result depending heavily on the speed at which it shifted; the CVT showed a 4.3% reduction against single-stage in one lap test. Results agreed with published simulations. Limit: one custom vehicle, driver influence on results, and a single lap for the CVT.
Read the paper (free)An analysis of how spur gear size, pitch, face width and ratio affect total power loss from sliding, rolling and windage, plus bearing losses, across a range of speeds, torques and oil viscosities, checked against published data. Gear efficiencies were generally above 98% except at very low torque; large-diameter, fine-pitch gears had higher peak efficiency but worse part-load efficiency; and no-load tare losses were a significant share of full-load loss except at low speed. Limit: spur gears in isolation, not a complete motorcycle gearbox.
Read the report (free)A 100-speed gearbox could be built, but it gains at most about 9% average power and about 3% in 0-100 time with instant shifts, and loses badly with real ones: 12.7 s with a quickshifter and 31.4 s with manual shifts, against 8.2 and 9.1 s for six gears, while needing a 1.5 to 2 m shaft.
Calculated in this post from the simulation table and the step-ratio model above, built on the KTM 200 Duke's published gearing and power (moto-data.net) and the NS200 kerb weight (Bajaj owner's manual), with these example inputs.
A single gear cannot serve a petrol engine: first gear tops out at 43 km/h and sixth gear needs about 75 km/h of clutch slip. The deciding principle is the engine's narrow power band set against the cost of each torque interruption; for a manual motorcycle the optimum is five to eight ratios, and six is the common answer.
How sensitive is the answer to the assumptions?
- Shift time. This dominates. At 0.25 s, six gears win; at 0.05 s, six to ten tie; only at zero shift time do more gears help, and then by about 3%.
- Power band width. A peakier engine (say a 250 cc race single) has a narrower band, which favours closer ratios and more of them, which is why race bikes use six closely spaced gears. A torquey twin or an electric motor favours fewer.
- Spread. I kept the 200 Duke's 3.09 spread. A wider spread (a lower first for off-road, a taller top for touring) makes each step larger and nudges the optimum upward by a gear or so. Adventure bikes and scooters choose their spread for their job.
- Torque curve. Only two points of my torque curve are published; the others are estimates. Changing them shifts all times together but not the ranking.
If you want to dig further into the engine side, power and torque explained covers the band the gearbox is trying to stay in, and whether engine braking is bad for your bike covers downshifting. The rest of the engineering on this site is on the Yantra page.
What's new
What if next?
- What if you never changed the engine oil for 100 years? The gearbox shares that oil on most bikes, and it would grind long before the century ends.
- What if you rode nearly at the speed of light? No gear ratio helps when your mass grows without limit.
- What if a ceiling fan powered your motorcycle? A 75 W motor would need a very, very low first gear.
Questions people ask
Why do bicycles have more gears than motorcycles?
A cyclist's useful cadence band is narrow and the power is tiny, so small steps between ratios matter, and derailleur shifts cost little time. A motorcycle engine's power band is wider relative to its needs, and each shift interrupts much more power, so fewer, larger steps work better.
Would more gears make a motorcycle faster?
Only slightly, and only with near-instant shifts. In my simulation of a 200 cc bike, going from 6 to 10 gears cut 0-100 km/h time by about 3% with instant shifts and made it slower with a 0.25 s manual shift.
Why is top gear sometimes so close to fifth?
Because gearboxes are spaced for acceleration through the band, so the top steps are small. On the 200 Duke, fifth (1.045) to sixth (0.917) is a 14% step against 37% from first to second, so sixth feels like a slight overdrive rather than a new gear.
Calculated in this post from the 200 Duke's gear ratios (1.045, 0.917, 2.833 and 2.067, moto-data.net).
Is a CVT better than a geared gearbox?
A CVT keeps the engine at its best rpm with no shift gaps, which helps acceleration and fuel use, but belt CVTs lose more power to friction than a gear mesh. In an EV test by Spanoudakis and colleagues, a CVT cut energy use by 4.3% against a single fixed ratio.
Sources
- moto-data.net: KTM 200 Duke (2013) specifications (source for primary, gear and final ratios, 19 kW and 20 Nm)
- Bajaj Auto: Pulsar NS200 BS VI owner's manual (source for the 158 kg kerb weight)
- Newman, K. and Dekraker, P.: Modeling the effects of transmission gear count, ratio progression, and final drive ratio using ALPHA, SAE 2016-01-1143 (2016)
- Spanoudakis, P. et al.: Experimental research of transmissions on electric vehicles' energy consumption, Energies (2019) (source for 3.8% and 4.3%)
- Anderson, N. E. and Loewenthal, S. H.: Effect of geometry and operating conditions on spur gear system power loss, NASA TM-81426 (1980) (source for the 98% mesh efficiency and tare losses)
- Kirca, M. C. and McGordon, A.: Effect of rider position on the energy consumption of an electric motorcycle, University of Warwick (2023) (source for the 0.5 m² drag area)
- Rushlane: 2026 Honda NX500 E-Clutch India launch (2026)
- EV India: Matter AERA 2026 (2026)
- CycleChaos: Suzuki RM50 and RK66 (source for the 14-speed RK66, 18 hp at 18,000 rpm, and the 1969 one-cylinder, six-speed rule)
