Traction control, cornering ABS and ride-by-wire explained

A six-axis sensor, two wheel-speed rings and an electronic throttle now sit on Indian bikes under ₹3.5 lakh. Here is what each one measures, what changes at 30° of lean, and what the crash data says they are worth.

A 2024 TVS Apache RR 310 sports motorcycle parked, seen from the side
Photo: Ganesh Mohan T, CC BY-SA 4.0, via Wikimedia Commons

Cornering ABS is anti-lock braking that also knows the lean angle: a six-axis inertial measurement unit (IMU) tells the ABS how far the bike is leaned, and the system limits how fast brake pressure can rise so the tyre keeps enough grip to hold the corner. Traction control compares front and rear wheel speeds and, through a ride-by-wire throttle and the ignition, trims engine torque when the rear spins. The best field data say plain ABS cuts fatal crash involvement by about 22%; a 2025 German study of 55 riders found no measurable extra braking benefit from cornering ABS in its test bends.

Key takeaways
  • Six-axis IMU plus two wheel-speed sensors: that is all the hardware cornering ABS adds over plain ABS.
  • √(μ² − tan²θ): the braking left at lean θ. At 30° on a μ = 1.0 road, about 0.82 g; at 40°, about 0.42 g.
  • 22% fewer fatal crash involvements with standard ABS across 65 models (IIHS, 2021).
  • 20°: the lean from which cornering ABS intervened in Germany's 2025 BASt test, which found no shorter stopping distance.
  • Ride-by-wire is what lets traction control close the throttle smoothly instead of cutting sparks.

Five years ago these systems lived on ₹15 lakh superbikes. Now the KTM 390 Duke, the 390 Adventure and the TVS Apache RR 310 (with its optional kit) bring IMU-based rider aids into the ₹3-3.5 lakh class, and India is moving towards ABS on every new two-wheeler.

Marketing names blur what each piece of hardware does. This post takes the system apart: the sensors, the physics of braking while leaned, how traction control decides how much is too much, and what the independent research actually measured.

22%fewer fatal crash involvements with ABS (IIHS, 65 models)
15 per secondbrake pressure adjustments by the RR 310's ABS unit (TVS)
20°lean from which cornering ABS intervened in BASt's tests
2013year Bosch and KTM introduced cornering ABS

What sensors do cornering ABS and traction control use?

Three kinds, which the ECU and the ABS unit combine many times a second:

  • Wheel-speed sensors: a toothed ring and sensor at each wheel.
  • A six-axis IMU that reports acceleration and rotation rate about three axes.
  • A throttle position sensor on the grip, on ride-by-wire bikes, separate from the throttle valve.
SensorWhat it measuresWhat the system uses it for
Wheel-speed sensors (front and rear)Rotation speed of each wheel from a toothed tone ringLock-up detection for ABS; rear spin relative to front for traction control
IMU accelerometers (3 axes)Longitudinal, lateral and vertical accelerationBraking and acceleration level; with the gyros, the direction of gravity
IMU gyroscopes (3 axes)Roll, pitch and yaw rateLean angle, wheelie and stoppie detection, slope detection
Throttle grip sensor (ride-by-wire)What the rider is asking forThe ECU decides how far to open the throttle valve
Brake pressure sensors (on some units)Hydraulic pressure at front and rearCombined braking and pressure-rate control

Lean angle is not measured directly. The IMU integrates roll rate from the gyroscope, which drifts over time, and corrects that drift using the accelerometers' sense of gravity, which is noisy when the bike is accelerating.

The fusion of the two is where makers differ. TVS calls its unit a 6D IMU; KTM, Bosch and Continental use similar six-axis units.

Wheel speeds F + R6-axis IMUThrottle grip sensorECU + ABS unitslip, lean angle,pitch, rider demandBrake pressure F + RThrottle valveIgnition timingFuel injection cutABS acts on the brakes; traction control acts on throttle, ignition and fuel.
Where the signals go. Ride-by-wire is what lets traction control close the throttle smoothly instead of only cutting sparks.

Why is braking in a corner different from braking upright?

Because the tyre has one budget of grip to share between turning and braking. Upright, almost all of it can go to braking. Leaned over, part of it is already holding the bike on its line, so less is left for slowing down, and a front brake grabbed hard in a lean can lock the wheel or stand the bike up.

The story

Bosch's Motorcycle Stability Control, which Visordown called the first effective cornering ABS, reached showrooms on KTM's 2014-spec 1190 Adventure; owners of 2013 bikes could add it as a £335 software update. When Visordown's Steve Farrell tested it at Bosch's proving ground in Boxberg, Germany, he did what every riding instructor says never to do. Following a dotted circle across a wide open area, banked over, he braked as hard as he could on the front brake alone. The bike stood itself up and stopped without leaving its line. On one repeat the tyre squealed and the front snatched sideways for an instant before recovering. He tried it again after his toe had scraped the ground, with the same result. The only scare was that it stopped so fast he had to put a leg out to catch it.

Visordown: First ride, KTM 1190 Adventure with Bosch Motorcycle Stability Control

The friction circle

The friction circle puts numbers on it. In a steady turn at lean angle θ, the tyres must supply a sideways force equal to the weight times tan θ. If the tyre can give at most μ times the load in any direction, the braking that is left is μ² − tan² θ, square-rooted, in units of g.

Assume a friction coefficient μ of 1.0:

  • leaned 30°: about 0.82 g of braking left;
  • leaned 40°: about 0.42 g;
  • leaned 45°: none.
The friction circle (μ = 1.0) cornering: tan 30° = 0.58 g braking left √(1 − 0.58²) = 0.82 g 40°: 0.42 g braking → At 45° the cornering arrow reaches the rim: nothing left to brake with.
Grip is a circle, not two separate budgets. The more of it lean uses sideways, the shorter the arrow left for braking. Cornering ABS limits how fast brake pressure climbs toward that rim.

Use this to check what you just read:

How much braking is left at this lean angle?

The stand-up effect

There is also a steering effect. When a leaned tyre brakes, its contact patch sits to the inside of the wheel's centre plane, so the braking force acts through a lever about the steering axis and tries to steer the front into the turn, which stands the bike up and widens the line.

Cornering ABS addresses both problems: it lowers the allowed rate of brake pressure rise as lean increases, so grip is not exceeded abruptly, and on some systems it shares pressure to the rear.

How does cornering ABS decide how much brake to allow?

It uses lean angle to change the ABS's own control limits. Normal ABS watches each wheel's deceleration and slip, releases pressure when a wheel starts to lock and re-applies it, up to 15 times a second on the RR 310's unit according to TVS. Cornering ABS adds lean angle to that logic: the more lean, the gentler the pressure build-up and the earlier the intervention.

What the BASt test found

Germany's Federal Highway Research Institute (BASt) published the most detailed independent test in 2025. Fifty-five riders braked a KTM 790 Duke in a 20 m radius bend and on a 29 m circle, with a handlebar switch to flip between cornering ABS and standard ABS.

MeasureCornering ABS vs standard ABS
InterventionFrom about 20° of lean, earlier and at lower pressure
Front wheel speed dropReduced
Tendency to stand upReduced
Holding the marked lineNo better
Braking distanceDid not fall
Average decelerationLower than standard ABS

The rider was the bigger variable. Before braking, riders cut their lean: the median lean at the start of pressure modulation was 40-50% below the cornering lean, and only 17% of braking events reached the cornering ABS lean limit.

Put simply, most riders braking in a bend straighten up first, which is what the system is there to protect them from not doing.

A motorcycle racer leaned over in a corner on a mountain road course
Deep lean leaves little grip for braking. At 40° on a dry road, the friction-circle model leaves under half a g of braking.Photo: Hustvedt, CC BY-SA 3.0, via Wikimedia Commons

How does motorcycle traction control work?

Traction control compares rear wheel speed with front wheel speed: when the driven rear spins noticeably faster than the bike is travelling, it reduces engine torque until the slip falls back. The slip ratio is (rear wheel surface speed − vehicle speed) ÷ vehicle speed, with vehicle speed taken from the unpowered front wheel.

The ECU has three ways to cut torque, from fastest to smoothest:

  1. Fuel or spark cut: skips combustion events; very fast but abrupt, the stutter riders feel on early systems.
  2. Ignition retard: fires the spark later so each combustion makes less torque; fast and smoother.
  3. Throttle valve closing: needs ride-by-wire; the slowest to act but the smoothest and the only way to hold torque at a target rather than chop it.

Lean-sensitive (cornering) traction control adds the IMU's lean angle. Leaned over, the tyre has less spare grip for drive for the same reason it has less for braking, so the allowed slip is reduced as lean increases. Wheelie control uses the IMU's pitch angle, or a front wheel that stops turning at the same rate as the rear, to trim torque when the front lifts.

What does ride-by-wire add?

Ride-by-wire replaces the throttle cable with a sensor on the grip and a motor on the throttle body, so the ECU decides the actual throttle opening. That makes ride modes possible (the same grip movement gives a softer or sharper response), and it lets traction control, cruise control and launch control work smoothly.

The Royal Enfield Himalayan 450 shows ride-by-wire is useful even without traction control: its 42 mm throttle body is electronically controlled with selectable riding modes, while its rider aids are limited to switchable dual-channel ABS. KTM's 390 Duke uses its ride-by-wire for launch control, which in Track mode holds engine speed at 7,000 rpm, and for three ride modes.

A KTM 390 Duke naked motorcycle parked, seen from the side
The third-generation KTM 390 Duke brought cornering ABS, traction control, ride modes and launch control into the ₹3 lakh class in 2023.Photo: LoiR, CC BY-SA 4.0, via Wikimedia Commons

Which Indian motorcycles have cornering ABS and traction control?

As of late 2026, IMU-based cornering ABS is available on the KTM 390 Duke, the 390 Adventure range and the TVS Apache RR 310 with its paid kit. Several other bikes have traction control based on wheel speeds only, without lean sensing.

MotorcycleRide-by-wireABSTraction controlOther aidsSource
KTM 390 Duke (2024 on)YesCornering ABS, supermoto modeYes, switchable3 ride modes, launch controlAutocar India, KTM
KTM 390 Adventure X (July 2025 update)YesCornering ABSYesStreet, Rain, Off-road modes; cruise control and speed limiterAutocar Professional
KTM 390 Adventure Enduro R (2025)YesCornering ABSYesAdds quickshifter, navigationAutocar Professional
TVS Apache RR 310 (2024, Dynamic Pro kit)YesCornering ABS, 3 levelsCornering TCWheelie control, rear lift-off control, slope-dependent control, cornering cruise controlTVS, Autocar India, Visordown
Bajaj Pulsar NS400ZYesDual-channelYes; off only in Sport and Off-roadRoad, Rain, Sport, Off-road modesBajaj, Autocar India
Royal Enfield Himalayan 450YesDual-channel, switchableNot listedRiding modesRoyal Enfield spec sheet

The RR 310's package costs ₹16,000 extra as part of the Dynamic Pro kit. Reviews differed: Autocar India found the cornering ABS well calibrated on track, while judging the traction control intrusive enough that a quick rider would be faster with it off. That is a typical first-generation result, since slip targets are a calibration choice, not a fixed property of the hardware.

Does ABS actually reduce motorcycle crashes?

Yes, for standard ABS the evidence is strong. The Insurance Institute for Highway Safety matched 65 motorcycle models sold with and without optional ABS, using registration data from 2013-19 and fatal crash data from 2003-19, and found 22% fewer fatal crash involvements per 10,000 registered vehicle years with ABS.

Reduction in fatal crash involvement with ABS, by motorcycle type
See the data as a table
Reduction with ABS (%)
All types22
Standard and cruiser32
Touring and sport touring25
Sport19
Supersport12

Source: IIHS, Teoh (2021) · Fatal crash involvements per 10,000 registered vehicle years, US data; touring figure is approximate.

Cornering ABS has no comparable crash study yet. Bosch, which makes Motorcycle Stability Control, says about a quarter of motorcycle crashes happen in curves, which is the gap cornering ABS is designed for.

The system does what it claims at the wheel, but in controlled bends riders did not stop shorter or hold their lines better.

That is the honest state of knowledge from the BASt test. Its value is likely concentrated in the emergencies a test track cannot reproduce, where a rider grabs the front brake mid-corner.

Is India making ABS compulsory on all two-wheelers?

India already required ABS on two-wheelers above 125 cc. In June 2025 the Ministry of Road Transport and Highways issued a draft notification proposing ABS meeting IS 14664:2010 on every new L2-category two-wheeler, which covers machines above 50 cc or faster than 50 km/h, from 1 January 2026. In July 2025 the ministry turned down manufacturers' request to drop the requirement. The policy debate is covered in what India's ABS mandate means.

The physics of the lean these systems measure is in countersteering and lean angle explained, and the corporate story behind KTM's Indian electronics is in Bajaj and KTM's history. For what drives these engineering choices at a business level, the work page covers my product and marketing work.

Research behind this post

Motorrad Kurven-ABS (MOKABS): Motorcycle cornering ABSNico Erlinger, Marianne Kraut, Ernst Tomasch et al. · BASt report F 162 (Federal Highway Research Institute, Germany) · 2025

TU Graz and Factum compared cornering ABS with conventional ABS on a KTM 790 Duke with a switch between the two, using 55 riders of varied age, gender and experience in a 20 m radius bend and a 29 m circle, plus focus groups and an online survey. Cornering ABS intervened from about 20° of lean, modulated earlier and at lower pressure, and reduced the bike's tendency to stand up, but braking distance did not fall and mean deceleration was lower. Over 90% of survey respondents believed it prevents crashes. The limit: closed-course manoeuvres, one motorcycle and riders who mostly reduced lean before braking.

Read the report (free)
Motorcycle antilock braking systems and fatal crash rates: updated resultsEric R. Teoh · Insurance Institute for Highway Safety · 2021

IIHS used vehicle identification numbers to compare the same make, model and year of 65 motorcycles across 10 types, with and without optional ABS. ABS was associated with a statistically significant 22% reduction in fatal crash involvements per 10,000 registered vehicle years; 32% for standard and cruiser bikes, about 25% for touring, 19% for sport and 12% for supersport. Rider age, speeding, alcohol and helmet use were similar between groups. The limit: US fatal crashes only, and it covers conventional, not cornering, ABS.

Read the paper (free)

Questions people ask

Is cornering ABS worth paying extra for?

It is a real safety layer for the rare panic grab mid-corner, but the 2025 BASt study found no shorter stopping in normal bend braking. Standard dual-channel ABS delivers most of the proven benefit, about 22% fewer fatal crash involvements in IIHS data. Cornering ABS is worth having; it is not a substitute for braking practice.

Should I switch traction control off?

On sand, deep gravel or mud, some wheelspin helps the bike move, which is why KTM and Bajaj let you switch it off in off-road modes. On tarmac, especially wet or oily Indian roads, leave it on. A track rider may switch it off once a system proves intrusive, as Autocar India found with the RR 310.

Can a bike without ride-by-wire have traction control?

Yes, by cutting spark or fuel instead of closing the throttle. It works but feels harsher, because it removes whole combustion events. Ride-by-wire lets the ECU reduce torque progressively.

Why does my ABS lever pulse?

That is the valve releasing and re-applying pressure several times a second when a wheel approaches lock. TVS notes the pulsing is normal; keep squeezing rather than letting go.

Sources

  1. BASt report F 162: Motorrad Kurven-ABS (MOKABS) (2025)
  2. IIHS: Largest study of its kind strengthens argument for motorcycle ABS (2021)
  3. IIHS bibliography: Motorcycle antilock braking systems and fatal crash rates, updated results (2021)
  4. TVS Motor: Apache RR 310 rider's guide to dual-channel ABS (2020)
  5. Autocar India: 2024 TVS Apache RR 310 track review (2024)
  6. Visordown: TVS Apache RR 310 review, spec and features
  7. Autocar Professional: KTM launches updated 390 Adventure X and Enduro R (2025)
  8. Autocar India: New KTM 390 Duke revealed (2023)
  9. Royal Enfield: Himalayan 450 technical specifications
  10. Bajaj Auto: Pulsar NS400Z brochure (2024)
  11. Autocar India: ABS likely mandatory on all new bikes and scooters from January 2026 (2025)
  12. Business Standard: MoRTH turns down two-wheeler companies' plea against ABS (2025)
  13. Visordown: First ride, KTM 1190 Adventure with Bosch Motorcycle Stability Control (Boxberg test)
  14. Visordown: KTM's new stability control system can be added to 2013 bikes
  15. Motoring Research: Bosch on motorcycle ABS and crashes in curves
traction controlride-by-wireIMUmotorcycle ABSKTM 390 DukeTVS Apache RR 310Bosch MSCrider aids
Sapta

Sapta (Saptarshi Sarkar) is a mechanical engineer turned marketer in Bengaluru and a solo touring rider. He writes the seven Saptaverse blogs. Work with him or read more of RoadHook Machines.

Keep reading in RoadHook Machines

From the other blogs