What if a motorcycle were the size of an ant, or an elephant?

Shrink a Pulsar NS200 to 8 mm and it becomes 252 times stronger for its weight but its engine cannot burn fuel. Grow it to 6 m and the same frame carries three times the stress. The square-cube law does all the work.

A Bajaj Pulsar 200 NS motorcycle parked, seen from the side
Photo: 25 Cents FC, CC BY-SA 3.0, via Wikimedia Commons

If a motorcycle were the size of an ant, it would be absurdly strong for its weight: shrink a 2,017 mm Pulsar NS200 to 8 mm and the stress in every part drops 252 times, so it could fall off a table and ride away. It would not run, though, because a 0.29 mm bore is ten times smaller than the smallest piston engine anyone has fired. Grow the same bike to elephant size (6 m long, about 4.3 tonnes) and every part carries three times the stress, the tyres need 85 psi just to stand still, and it needs thicker, not just bigger, bones.

Calculated in this post from the Pulsar NS200 owner's manual (2,017 mm, 158 kg, 28 psi rear), a chosen scale factor of 1/252 (8 mm) or 3 (about 6 m), and the 3 mm smallest piston engine in Fernandez-Pello (2002); the 85 psi is the 28 psi rear pressure times 3.

Key takeaways
  • Scale a bike by k and the stress in every part scales by k: that is the square-cube law.
  • An 8 mm NS200 (k = 1/252) weighs about 9.9 mg and is 252 times further from breaking.
  • Its engine cannot run: a 0.29 mm bore is ten times below the smallest piston ever fired (3 mm).
  • A 6 m NS200 (k = 3) weighs 4,266 kg, carries 3x the stress and needs about 85 psi in its tyres.
  • To fix it, tubes must grow 5.2 times fatter, not 3, the same trick elephants use.

The rule behind both answers is the square-cube law. This is a thought experiment with a straight face. I take one real motorcycle, the BS6 Bajaj Pulsar NS200, keep its exact shape and materials, and scale it like a photocopier: everything multiplied by the same factor.

Then I ask what the steel, rubber, air and fuel do about it. Biology has already run this experiment a million times, from 2 mg ants to 4.6 t elephants, so the answers can be checked against animals.

252xlower stress in an ant-sized NS200 (scale factor 1/252)
3xhigher stress in an elephant-sized NS200 (scale factor 3)
0.29 mmbore of the ant-bike engine, against a 3 mm smallest demonstrated piston
24.5 km/hfastest recorded elephant in a 68-animal dataset (Ruiz et al., 2025)

What is the square-cube law, in one paragraph?

The square-cube law says that when you scale an object by a factor k in every direction, its areas grow by k squared and its volume and mass grow by k cubed. Galileo used it in 1638 to argue that giants and huge trees cannot simply be scaled-up humans and saplings.

The story

Galileo's last book had trouble finding a printer. The Roman Inquisition had banned publication of his works, and attempts to publish in France, Germany and Poland failed, so Two New Sciences finally appeared in 1638 in Leiden, in the Dutch Republic, printed by Lodewijk Elzevir. It is a dialogue over four days between three characters, Salviati, Sagredo and Simplicio.

On the second day they work out the strength of beams, and reach a conclusion that sounds obvious only once you have heard it: a structure built in the same proportions, only bigger, is weaker, so the bones of larger animals must be proportionately thicker. Historians now call that bone argument possibly the first quantitative result in biology. About fifty copies reached Rome's bookshops in January 1639 and sold quickly.

Wikipedia: Two New Sciences

The consequence for anything that has to hold itself up is direct. Weight goes with volume, but the strength of a beam, a bone, a tyre patch or a weld goes with the area of its cross-section. So stress, which is force divided by area, grows in proportion to k itself.

\[ \sigma = \frac{F}{A} \propto \frac{k^3}{k^2} = k \]

Double the size and you double the stress in every part, before the bike has moved a metre. Halve it and the stress halves. That single line explains why ants can survive a fall from any height and why there are no 50-tonne horses.

Double the size and you double the stress in every part, before the bike has moved a metre.The working above
Scale by k: area k², mass k³, stress kk = 1k = 2k = 3Area 1Area 4Area 9Mass 1Mass 8Mass 27Stress 1Stress 2Stress 3Weight grows with volume, strength with area,so every part works harder as the bike grows.
The square-cube law in three blocks. The k = 3 block is the elephant NS200: 27 times the mass resting on 9 times the area.

The rest of this post is that line applied, part by part, with real numbers.

What are the starting numbers for a real Pulsar NS200?

The BS6 Pulsar NS200 owner's manual gives a length of 2,017 mm, a kerb weight of 158 kg, a 199.4 cc single with a 72 mm bore and 49 mm stroke, 24.5 PS (18.0 kW) at 9,750 rpm, 18.74 Nm at 8,000 rpm, and a rear tyre pressure of 2 kgf/cm², about 196 kPa or 28 psi, for a solo rider. Those are the inputs. Two choices fix the scale factors:

  • Ant bike: 8 mm long, about the size of a large worker ant. The scale factor is \( k = 0.008 / 2.017 = 0.00397 \), or 1/252.

    Calculated in this post from the 2,017 mm length in the Pulsar NS200 owner's manual and the chosen 8 mm premise.

  • Elephant bike: mass close to a big Asian elephant. With k = 3 the bike is 6.05 m long and \( 158 \times 3^3 = 4{,}266 \) kg, inside the 0.1 to 4.6 t range of the elephants measured by Ruiz and colleagues.

    Calculated in this post from the 2,017 mm length and 158 kg kerb weight in the Pulsar NS200 owner's manual and the chosen scale factor k = 3.

A carpenter ant standing on a surface, shown in close-up
An ant-sized NS200 would be about as long as this carpenter ant and weigh about 10 mg. At that size the square-cube law flips almost every engineering problem upside down.Photo: Vengolis, CC BY-SA 4.0, via Wikimedia Commons

What happens to an ant-sized motorcycle?

An ant-sized motorcycle would be structurally almost indestructible and practically useless as a petrol machine. Its mass is 158 kg times \( (1/252)^3 \), which is about 9.9 mg, and every load-bearing part carries 1/252 of the stress it does on the road today.

Take a fall. A full-size bike tipped off a cliff would reach a terminal velocity where drag equals weight. Using a bare-bike drag area of about 0.3 m², close to the 0.26 to 0.31 m² measured for four bare motorcycles in a Warwick wind tunnel study, the number is:

\[ v_t = \sqrt{\frac{2mg}{\rho C_d A}} = \sqrt{\frac{2 \times 158 \times 9.81}{1.225 \times 0.30}} \approx 92\ \text{m/s} \]

Mass scales as k cubed and drag area as k squared, so terminal velocity scales as the square root of k. The ant bike tops out at about \( 92 \times \sqrt{0.00397} \approx 5.8 \) m/s, roughly 21 km/h, and its frame is 252 times further from its strength limit.

Calculated in this post from the 92 m/s terminal velocity above, the scale factor 1/252, and the 0.26 to 0.31 m² bare-bike drag areas in Kirca and McGordon (Warwick, 2023).

Ants live in this world. Engineers at Ohio State spun Allegheny mound ants in a centrifuge and found the neck joint only started to stretch at about 350 times body weight and ruptured at 3,400 to 5,000 times body weight, according to the university's 2014 release on the Journal of Biomechanics study. Small bodies are strong bodies.

What starts to matter at 8 mm

The forces that do matter at 8 mm are the ones that scale with length or area, not volume. Surface tension acts along an edge, so it scales as k; weight scales as k cubed. Their ratio grows as \( 1/k^2 \), which for the ant bike is \( 252^2 \approx 63{,}500 \) times larger than for a real bike.

A single dew drop around the contact patch could hold the bike in place the way it pins a real ant. Air also behaves differently: the Reynolds number \( Re = \rho v L / \mu \) falls from about 5 million for a real bike at 130 km/h to roughly 20,000 for the ant bike at the same speed, where drag coefficients start to rise.

Calculated in this post from Re = ρvL/μ with these example inputs: an assumed speed of 130 km/h (not a measured top speed), lengths of 2.017 m and 8 mm from the Pulsar NS200 owner's manual and the chosen scale, and sea-level air density 1.225 kg/m³ and viscosity 1.79 × 10⁻⁵ kg/m/s from the International Standard Atmosphere.

Could an ant-sized petrol engine actually run?

No. The scaled engine has a bore of 72/252 = 0.29 mm and a swept volume of about 0.012 mm³, and a hydrocarbon flame in a chamber that small loses heat and radicals to the walls faster than it can burn. In his 2002 review of micro-scale combustion, Carlos Fernandez-Pello of UC Berkeley reported that the smallest piston-cylinder unit to achieve compression ignition was 3 mm in diameter, and it ran for only several cycles, limited by sealing and materials. The ant bike's bore is ten times smaller than that.

The same review explains why people keep trying:

  • Energy density. Liquid hydrocarbons carry about 45 MJ/kg against about 1.2 MJ/kg for the best lithium cells it lists, so even a 3% efficient micro-engine would compete with a battery.
  • Quenching is not a hard wall. The quenching distance falls roughly with the inverse square root of wall temperature, so very hot walls help.

For an 8 mm bike, though, the honest engineering answer is an electric motor or a magnetic drive. That is exactly what working insect-scale machines use: a 21 mg, 9.4 mm flying robot published in Science Advances in March 2025 is powered by an external alternating magnetic field, not a fuel tank.

How fast would the ant bike go, and at what rpm?

Surprisingly, about as fast as the real one, if you could power it. Engine power is set by swept volume, rpm and mean effective pressure. Mean piston speed is limited by materials and friction, so a scaled engine keeps the same piston speed, which means rpm scales as 1/k:

\[ \bar{v}_p = \frac{2 S N}{60} = \frac{2 \times 0.049 \times 9750}{60} = 15.9\ \text{m/s} \]

Keep 15.9 m/s, shrink the stroke 252 times, and the ant engine spins at about 2.46 million rpm. Power is volume times rpm, so it scales as \( k^3 \times k^{-1} = k^2 \): 18.0 kW becomes 0.28 W. Aerodynamic drag power also scales as area, k squared. At top speed the two balance:

Calculated in this post from the 49 mm stroke and 9,750 rpm in the Pulsar NS200 owner's manual and the scale factor 1/252.

\[ P = \tfrac{1}{2} \rho \, C_d A \, v^3 \;\Rightarrow\; v^3 \propto \frac{P}{A} \propto \frac{k^2}{k^2} = \text{constant} \]

So on paper the ant bike has the same top speed as an NS200, about 130 km/h, and a power-to-weight ratio of \( 0.28 / 9.9\times10^{-6} \approx 28{,}600 \) W/kg against 114 W/kg for the real bike. In practice the higher drag coefficient at low Reynolds number and the engine that cannot burn would pull it well below that. Treat the 130 km/h as the scaling ceiling, not a prediction.

Quantity (scales as)Ant bike, k = 1/252Real NS200, k = 1Elephant bike, k = 3
Length (k)8 mm2,017 mm6,051 mm
Mass (k³)9.9 mg158 kg4,266 kg
Stress in every part (k)0.004x1x3x
Rear tyre pressure to keep the same patch shape (k)0.78 kPa196 kPa (28 psi)588 kPa (85 psi)
Bore (k)0.29 mm72 mm216 mm
Swept volume (k³)0.012 mm³199.4 cc5,384 cc
Peak-power rpm at equal piston speed (1/k)2.46 million9,7503,250
Power (k²)0.28 W18.0 kW162 kW
Power-to-weight (1/k)28,600 W/kg114 W/kg38 W/kg
Free-fall terminal velocity (√k)5.8 m/s92 m/s159 m/s

What happens to an elephant-sized motorcycle?

An elephant-sized NS200 would be overloaded before it moved: at k = 3 it weighs 4,266 kg and every tube, weld, spoke and bearing carries three times the stress it was designed for. Whatever margin the real bike has against a pothole at speed, the big one has a third of it.

Tyres: 85 psi just to stand still

The tyres show it most clearly. A tyre carries load with air pressure acting on the contact patch, so the patch area is roughly load divided by pressure. At three times the size the load is 27 times larger, but a geometrically similar patch is only 9 times larger.

To keep the same shape the pressure must triple, from 196 kPa to about 588 kPa (85 psi). Run it at 28 psi and the patch would have to be three times too long, with sidewalls folding far more than the design allows.

Engine: a 5.4-litre single

The engine has the opposite problem: a single cylinder with a 216 mm bore and 5.4 litres of swept volume, turning only 3,250 rpm for 162 kW. Torque scales with displacement, so 18.74 Nm becomes about 506 Nm.

Calculated in this post from the 72 mm bore, 199.4 cc, 18.0 kW and 18.74 Nm in the Pulsar NS200 owner's manual and the chosen scale factor k = 3.

An Indian elephant bull standing in forest at Bandipur National Park
An Asian elephant bull in Bandipur National Park, Karnataka. Elephants of this size stand on near-vertical, column-like legs, which is nature's answer to the stress problem an elephant-sized bike would face.Photo: Yathin S Krishnappa, CC BY-SA 3.0, via Wikimedia Commons

How do real elephants solve the problem the big bike cannot?

Animals cheat the square-cube law with posture and proportion, and the numbers are well measured. Andrew Biewener's 2005 review in the Journal of Experimental Biology shows that under pure geometric scaling, peak bone stress would rise as body weight to the power 0.28 to 0.33. Mammals from mice to horses avoid that by standing more upright: the effective mechanical advantage of their limbs rises as body mass to the 0.25 power, so muscles need less force per unit of body weight and bone stress stays roughly constant from 0.04 kg to 300 kg.

Above about 300 kg the trick runs out and animals change shape instead: thicker bones relative to length, straighter legs, and less athletic movement. Ruiz and colleagues (2025) assembled maximum-speed data for 68 elephants from 0.1 to 4.6 t; the fastest reached 24.5 km/h, and every one of them sat below the speed predicted by general mammal models for its mass. Their upper-limit estimates for heavier extinct proboscideans fall steadily as mass rises, which is the square-cube law expressed as a speedometer.

Upper-limit top speed of giant proboscideans falls with body mass
See the data as a table
H-model upper limit (km/h)G-regression upper limit (km/h)
6 t20.321.1
8 t18.619.6
9.5 t17.618.7
10.5 t17.118.2
11 t16.818.0
13 t16.017.2
16 t14.916.1

Source: Ruiz et al., Scientific Reports (2025), values for Mammuthus, Mammut, Deinotherium and Palaeoloxodon species · Upper limits, not measured speeds. Live elephants up to 4.6 t topped out at 24.5 km/h.

What would it take to make the elephant bike work?

Keep the stress the same as the real bike by making every load path thicker than geometric scaling says. If load grows as k cubed and you want stress to stay constant, cross-section area must also grow as k cubed, so a round tube's diameter (for the same wall proportions) grows as k to the 1.5:

  1. Set the target. Same stress as the real NS200: \( \sigma_3 = \sigma_1 \).
    \[ \frac{F_3}{A_3} = \frac{F_1}{A_1} \;\Rightarrow\; A_3 = A_1 \frac{F_3}{F_1} = 27 A_1 \]
  2. Convert area to diameter. For geometrically similar tube sections \( A \propto d^2 \):
    \[ d_3 = d_1 \sqrt{27} = 5.2\, d_1 \]
    So tubes 5.2 times fatter, not 3 times, on a bike only 3 times longer. This is the same allometry Biewener describes for big animals.
  3. Count the cost in mass. Thicker sections add mass, which adds load. Each 1% of extra structure mass needs about 1% more area, so the solution converges, but the frame ends up a larger share of total mass. This is a known feature of large animals too: the skeleton is a bigger fraction of an elephant than of a mouse.
  4. Fix the tyres. Either triple pressure to 588 kPa, which is truck-tyre territory, or make the tyre wider than scaling suggests so the patch grows faster than k squared.
  5. Accept slower dynamics. For gravity-driven motion the natural time scale is \( t \propto \sqrt{L/g} \), so the elephant bike tips, weaves and recovers \( \sqrt{3} = 1.7 \) times more slowly. It would feel stable and lazy, like riding a ship.
Frame tube, seen end-onRealdScaled x33d, stress 3xNeeded5.2d, stress 1xArea must grow 27x (k³), so diameter grows √27 = 5.2x
Why the elephant bike cannot just be a photocopy. Only the right-hand tube keeps the stress of the real NS200; drawn to scale relative to each other.
Verdict: possible with changes

The elephant-sized NS200 works only if you break geometric similarity: tubes about 5.2 times thicker instead of 3, tyres at about 85 psi or much wider, and a 5.4-litre, 506 Nm single turning 3,250 rpm. The ant-sized NS200 is structurally safe by a factor of 252 but cannot be a petrol bike, because its 0.29 mm bore is ten times below the smallest demonstrated piston engine; with an electric or magnetic drive it becomes possible. The law that decides both is the square-cube law: stress grows in direct proportion to size.

Calculated in this post from the Pulsar NS200 owner's manual, the scale factors above, and the 3 mm smallest compression-ignition piston in Fernandez-Pello (2002).

How sensitive are these answers to the assumptions?

The structural conclusions are robust; the speed numbers are not. Here is what moves if an assumption changes.

  • Different scale target. Stress scales linearly, so an elephant bike at k = 2.5 (5 m, about 2.5 t) carries 2.5 times the stress, not 3. Halving the length halves the stress. Use the calculator below.

    Calculated in this post from the 158 kg kerb weight and 2,017 mm length in the Pulsar NS200 owner's manual and the example scale k = 2.5.

  • Engine scaling rule. I held mean piston speed constant. If instead you held rpm constant (impossible for the ant engine, plausible for a mid-size one), power would scale as k cubed and the elephant bike would make 486 kW. Real big engines run lower piston speeds, so the k-squared rule is the better guide.

    Calculated in this post from the 24.5 PS (18.0 kW) in the Pulsar NS200 owner's manual times k cubed (27) for k = 3.

  • Drag area. The 0.3 m² bare-bike value comes from measured motorcycles of 0.26 to 0.31 m². Using 0.26 raises terminal velocity by about 7%. It does not change any scaling exponent.
  • Material strength. Steel does not get stronger or weaker with size to first order, but very large castings and welds have more room for defects, which lowers usable strength. That pushes the elephant bike further toward the impossible side.

Scale a Pulsar NS200 yourself

An Asian elephant walking through a shallow river at golden hour
An Asian elephant walking through a river in Laos. Elephants keep at least one foot on the ground at all speeds, a gait choice that keeps peak limb loads down.Photo: Basile Morin, CC BY-SA 4.0, via Wikimedia Commons

Where does this model break down?

Pure geometric scaling is a first approximation, and it fails at both ends for different reasons:

  • At ant scale, the model ignores that combustion, lubrication and air all behave differently: oil films in a 0.29 mm bore would be a large fraction of the clearance, and the Reynolds number drops by a factor of about 250.
  • At elephant scale, it ignores fatigue.

Biewener notes that compact bone fails in fatigue at stress amplitudes of only 50 to 100 MPa, far below its single-load strength; metal frames have the same weakness, and tripling the stress amplitude cuts fatigue life by far more than three times. So the elephant bike's fatigue problem is worse than its static one.

The rider also breaks the model. A real rider weighs roughly half as much as the bike, and I left the rider out of both versions.

A human on the ant bike is not possible; a human on the elephant bike adds only 2% to its mass and would be a passenger on a machine with a 3-tonne-plus kerb weight. If you want the riding-dynamics side of this, the post on rake, trail and chassis geometry explains which numbers scale and which do not, and countersteering physics shows why the bigger, slower bike would need more input to turn.

For the power side, how power and torque relate covers the piston-speed idea used above, and single versus twin cylinders explains why nobody builds a 5.4-litre single: makers split big engines into more, smaller cylinders for exactly the square-cube reasons in this post. Tyre load and pressure are covered in reading tyre size markings. The broader engineering world of the site is on the Yantra page.

What does the research say about scaling and strength?

Biomechanical consequences of scalingAndrew A. Biewener · Journal of Experimental Biology 208(9): 1665-1676 · 2005

A review of how bone, muscle and tendon loads change with body size across terrestrial mammals and birds. Under geometric similarity peak bone stress should rise as body weight to the 1/3; measured limb bones scale close to geometric (length proportional to diameter to the 0.89).

Mammals offset this by raising limb effective mechanical advantage as mass to the 0.25, keeping bone and muscle stress roughly constant from 0.04 to 300 kg. The author estimates fast runners would exceed a bone strength of about 240 MPa above roughly 20 kg if they did not change posture. Limit: most data come from animals under 300 kg, so the largest mammals are extrapolated.

Read the paper (free)
The body mass-maximum speed relationship and the athletic capability of giant proboscideans and sauropodsJavier Ruiz, Anthony Romilio, Juha Saarinen et al. · Scientific Reports · 2025

The authors fitted body mass against top speed for 150 land mammal species (9 g to 6 t), added the fastest measured Asian and African elephants, and derived upper-limit speeds for animals too big to measure.

Maximum speed peaks near 65 kg in their regression and falls beyond it. All 68 measured elephants (0.1 to 4.6 t, top speed 24.5 km/h) sat below both models' lower bounds; a 16 t Mammut borsoni gets an upper limit of about 15 to 16 km/h and a 75 t titanosaur about 9 km/h. Limit: these are ceilings for graviportal animals, not speeds those animals actually reached.

Read the paper (free)
Micropower generation using combustion: Issues and approachesA. Carlos Fernandez-Pello · Proceedings of the Combustion Institute 29 · 2002

A topical review of combustion devices in the milliwatt-to-watt range. It sets out the case (hydrocarbons at about 45 MJ/kg against 1.2 MJ/kg for lithium cells), the physics of small-scale flames (heat and radical loss to walls, residence time versus chemical time) and the state of hardware: compression ignition had been achieved in a 3 mm diameter piston-cylinder for several cycles, and a free-piston generator with 13.4 cm³ displacement had produced 12 W. Limit: the review is from 2002, and micro-engine efficiency has remained the bottleneck since.

Read the paper (free)

What if next?

Questions people ask

Why can ants lift so much more than their body weight?

Muscle force depends on cross-sectional area, which scales as size squared, while body weight scales as size cubed. A small animal therefore has far more force per kilogram. Ohio State's centrifuge tests found an ant's neck joint ruptured only at 3,400 to 5,000 times body weight.

Could a giant motorcycle ever be built?

Yes, but not by scaling up an existing design. Every part has to grow faster than the bike's length: tube diameters about 5.2 times larger for a bike three times longer, tyres at about three times the pressure, and the engine split into several cylinders.

Would a tiny motorcycle be faster than a real one?

Its power-to-weight ratio would be enormous, about 28,600 W/kg at ant size against 114 W/kg for an NS200, so it would accelerate far harder. Its drag-limited top speed is the same on paper, because both power and drag area scale with size squared. In reality, thicker air at small scale would slow it.

What is the biggest land animal possible?

There is no single hard number, but speed and agility fall steadily with mass. Ruiz and colleagues put upper speed limits of about 10 km/h on 50 t sauropods and about 9 km/h on a 75 t Argentinosaurus. Beyond that, an animal is close to only walking.

Sources

  1. Bajaj Auto: Pulsar NS200 BS VI owner's manual (source for the 2,017 mm length, 158 kg kerb weight, 72 x 49 mm bore and stroke, 24.5 PS at 9,750 rpm, 18.74 Nm, and 28 psi rear pressure)
  2. Biewener, A. A.: Biomechanical consequences of scaling, Journal of Experimental Biology (2005) (source for bone stress scaling, the M^0.25 mechanical advantage, the 0.04 to 300 kg range and bone fatigue figures)
  3. Ruiz, J. et al.: The body mass-maximum speed relationship and the athletic capability of giant proboscideans and sauropods, Scientific Reports (2025) (source for the 68-elephant dataset, the 24.5 km/h top speed and the chart values)
  4. Fernandez-Pello, A. C.: Micropower generation using combustion: Issues and approaches, Proceedings of the Combustion Institute (2002) (source for the 3 mm smallest compression-ignition piston, 45 MJ/kg and 1.2 MJ/kg, and quenching behaviour)
  5. Ohio State University: With their amazing necks, ants don't need high hopes to do heavy lifting (2014) (source for the 350x and 3,400 to 5,000x body weight neck figures)
  6. Kirca, M. C. and McGordon, A.: Effect of rider position on the energy consumption of an electric motorcycle, University of Warwick (2023) (source for bare-bike drag areas of 0.26 to 0.31 m²)
  7. Berkeley Sensor and Actuator Center: Untethered subcentimeter flying robots (2025) (source for the 21 mg, 9.4 mm magnetically driven robot)
  8. MIT News: MIT engineers design an aerial microrobot that can fly as fast as a bumblebee (2025)
  9. Physics Forums: How does the square-cube law limit animal size? (reader question used for the framing)
  10. Wikipedia: Two New Sciences (source for the story: 1638 Leiden printing, Day Two bone argument)
square-cube lawscalingGalileoallometrybone stressmicro-combustionPulsar NS200what if
Sapta

Sapta (Saptarshi Sarkar) is a mechanical engineer turned marketer in Bengaluru and a solo touring rider. He writes the seven Saptaverse blogs. Work with him or read more of RoadHook Machines.

Keep reading in RoadHook Machines

From the other blogs