What would riding a motorcycle on the Moon feel like?

Weightless jumps, slow-motion falls and brakes that take six times as far to stop. Apollo's rover crawled at 16 km/h for good reasons, and the physics explains every one.

Apollo 15 astronaut James Irwin saluting beside the flag with the Lunar Roving Vehicle and lunar module on the Moon in 1971
Photo: Astronaut David R. Scott, Apollo 15 commander., Public domain, via Wikimedia Commons

Riding a motorcycle on the Moon would feel floaty and slow-motion, but dangerously slippery. With gravity at 1.62 m/s², one-sixth of Earth's, your tyres press down with one-sixth the force, so braking, cornering and acceleration grip all fall to one-sixth: stopping from 60 km/h would take about 107 m instead of 18 m. Jumps would carry six times as far and hang in the air six times as long, yet you would land just as hard, because your mass has not changed. Rubber tyres would not survive, which is why Apollo's rover rolled on wire mesh at a top speed of about 16 km/h.

Calculated in this post from lunar gravity of 1.62 m/s² (NASA Moon fact sheet) and Earth gravity of 9.81 m/s² (NIST), with these example inputs: a grip coefficient of 0.8, a 250 kg bike and rider, and a 60 km/h start. The 107 m and 18 m are not measured stopping distances.

Key takeaways
  • 1.62 m/s² lunar gravity cuts every kind of tyre grip to one-sixth of Earth's.
  • 107 m to stop from 60 km/h on the Moon, against about 18 m on dry Earth asphalt (calculated with NASA's lunar gravity and an assumed grip of 0.8).
  • 37 m and 5.1 s of flight from a 30° ramp at 30 km/h, against 6 m and 0.85 s on Earth.
  • Same landing speed: mass does not change, so you hit the ground just as hard.
  • 95–390 K surface temperatures and abrasive dust rule out rubber tyres and plain seals.

This is a tier-2 what-if, so it is solved properly: assumptions, the laws that apply, numbers carried through, a sensitivity check and a verdict. The sources are NASA's own engineering reports from the Apollo rover programme.

The story

In December 1972, at the end of the first of three moonwalks on Apollo 17, Gene Cernan's hammer, carried in a suit pocket, caught the rear right fender extension of the rover and knocked it off. He taped it back with duct tape, but lunar dust stopped the tape sticking and the fender fell off again while they drove. Without it, the wheels threw up plumes of dark dust that coated suits and instruments, and dark dust soaks up sunlight.

That night, a team in Houston designed a fix from four laminated lunar maps taped together and held on with two clamps from the optical alignment telescope. Cernan and Harrison Schmitt fitted it the next morning and the mission carried on. The maps are now at the National Air and Space Museum.

Smithsonian National Air and Space Museum: Duct tape auto repair on the Moon

What are the assumptions?

I compare the same bike and rider on Earth and on the Moon. Where a number is my estimate, the table says so.

SymbolMeaningValue used
gEEarth gravity9.81 m/s²
gMMoon gravity1.62 m/s² (0.165 of Earth)
μTyre-to-ground friction coefficient0.8 (estimate for dry asphalt), 0.5 tested as a sensitivity
mBike plus suited rider250 kg (estimate)
hHeight of centre of mass0.6 m (estimate)
vTest speeds16, 30 and 60 km/h

I assume, generously, that a lunar tyre grips regolith as well as a road tyre grips tarmac. NASA's own wheel tests suggest real traction is lower, so treat every Moon figure here as a best case.

Why would your brakes be six times worse?

Friction force equals μ times the normal force, and the normal force is your weight. On the Moon your 250 kg bike weighs what a 41 kg one weighs on Earth, but it still has 250 kg of inertia to stop. This is Coulomb's friction law meeting Newton's second law.

Calculated in this post from the 250 kg example bike and rider, lunar gravity of 1.62 m/s² (NASA) and Earth gravity of 9.81 m/s² (NIST): 250 × 1.62 / 9.81 = 41 kg.

\[ a_{max} = \frac{\mu m g}{m} = \mu g, \qquad d_{stop} = \frac{v^2}{2 \mu g} \]

The mass cancels, so the stopping distance depends only on speed, grip and gravity.

  1. Earth, 60 km/h. \( v = 16.67 \) m/s, \( a = 0.8 \times 9.81 = 7.85 \) m/s², \( d = 277.8 / 15.7 = 17.7 \) m.
  2. Moon, 60 km/h. \( a = 0.8 \times 1.62 = 1.30 \) m/s², \( d = 277.8 / 2.59 = 107 \) m.
  3. Moon, rover speed. At the LRV's sustained 16 km/h (4.44 m/s): \( d = 19.75 / 2.59 = 7.6 \) m, against 1.3 m on Earth.
  4. Sensitivity. If regolith only gives μ = 0.5, the 60 km/h stop stretches to 172 m.

Calculated in this post with d = v²/(2μg), from lunar gravity of 1.62 m/s² (NASA), Earth gravity of 9.81 m/s² (NIST), the LRV's 16 km/h (Asnani et al., 2009) and an assumed grip of 0.8. These are example inputs, not measured stops.

Stopping distance at maximum grip, Earth vs Moon (μ = 0.8)
See the data as a table
Earth (9.81 m/s²) (m)Moon (1.62 m/s²) (m)
10 km/h0.53.0
20 km/h2.011.9
30 km/h4.426.8
40 km/h7.947.6
60 km/h17.7107.2

Source: Calculated from d = v²/(2μg) with gravity from the NASA Moon fact sheet · Braking only, no reaction time. Real lunar soil likely grips less than μ = 0.8.

Your reaction time does not shrink either. Add one second of thinking before the brakes bite and the 60 km/h stop on the Moon grows to about 124 m. Speed is the thing a lunar rider cannot afford.

Calculated in this post: the 107 m braking distance (lunar gravity from the NASA Moon fact sheet) plus 16.7 m travelled in one assumed second at 60 km/h (16.67 m/s), giving about 124 m. The one-second delay is an example input.

How would cornering feel?

The lean angle would feel normal, but you would have to take every corner at 40% of your Earth speed. In a steady turn, the tyres must supply the centripetal force, and the most they can give is μmg.

\[ \frac{m v^2}{r} \le \mu m g \;\Rightarrow\; v_{max} = \sqrt{\mu g r}, \qquad \tan\theta_{lean} = \frac{v^2}{g r} \le \mu \]
  1. Earth, 20 m radius. \( v = \sqrt{0.8 \times 9.81 \times 20} = 12.5 \) m/s, or 45 km/h (g from NIST).
  2. Moon, same corner. \( v = \sqrt{0.8 \times 1.62 \times 20} = 5.1 \) m/s, or 18 km/h (g from the NASA Moon fact sheet).
  3. Lean at the limit. \( \tan\theta = \mu = 0.8 \), so θ = 38.7° on both worlds.

Calculated in this post with v = √(μgr), using the example inputs of a 20 m corner radius and a grip of 0.8, with gravity from NASA and NIST.

That last line surprises people. Gravity cancels out of the lean angle. At the limit you would hang off at exactly the same angle as on Earth, just much more slowly, which is why countersteering would still work but feel lazy.

The Apollo 17 lunar rover with its replacement fender made of taped maps clamped to the right rear wheel
The Apollo 17 rover with its map-and-clamp replacement fender on the right rear wheel. Losing a fender meant a rooster tail of dust over everything.Photo: NASA, Public domain, via Wikimedia Commons

How far would a jump go?

Six times farther, six times higher and six times longer in the air. Projectile range and flight time both divide by g, so on the Moon they multiply by 6.06. Take a 30° ramp at 30 km/h (8.33 m/s), ignoring the short ramp height.

Calculated in this post from the gravity ratio 9.81 / 1.62 = 6.06 (NIST, NASA). The 30° ramp at 30 km/h is an example input, not a stunt anyone has measured.

\[ R = \frac{v^2 \sin 2\theta}{g}, \qquad t = \frac{2 v \sin\theta}{g}, \qquad H = \frac{(v \sin\theta)^2}{2g} \]
QuantityEarthMoon
Distance R6.1 m37.1 m
Time in the air0.85 s5.1 s
Peak height H0.88 m5.4 m
Vertical speed at landing4.2 m/s4.2 m/s
Vertical landing energy (250 kg)2.2 kJ2.2 kJ

The landing hits exactly as hard on the Moon as on Earth, because you come down at the same speed you went up, and your mass is unchanged. The flight is longer and floatier, but the suspension and your spine meet the same 2.2 kJ.

Earth: 6 m, 0.85 sMoon: 37 m, 5.1 s in the airpeak 5.4 m above the ramp liplands at the same 4.2 m/sdownward speedSame bike, same 30° ramp, same 30 km/h. Horizontal scale squeezed.
A lunar jump. Range and airtime scale with 1/g, so the Moon multiplies both by about six, but the landing speed does not change.

Would the bike feel stable, or would it fall over?

It would balance itself at walking pace, and every wobble and fall would happen in slow motion. A bike's self-balancing behaviour depends on the balance between gravity and its speed and size, captured by the Froude number, \(Fr = v^2/(gL)\). Kooijman and colleagues noted that self-stability tends to appear near speeds of order \(\sqrt{gL}\).

\[ v_{Moon} \approx v_{Earth}\sqrt{\frac{g_M}{g_E}} = 4.3 \times \sqrt{0.165} = 1.75\ \text{m/s} \]

The benchmark bicycle of Meijaard and colleagues becomes self-stable at 4.3 m/s on Earth. Scaled to lunar gravity, that would be about 1.75 m/s, or 6.3 km/h. This scaling is my approximation; gyroscopic terms do not scale exactly with g. Falls slow down too. An upright bike tips like an inverted pendulum with time constant \(\tau = \sqrt{h/g}\).

Calculated in this post by scaling the 4.3 m/s weave speed by √(1.62 / 9.81) = 0.41, which gives 1.75 m/s (6.3 km/h). The scaling is an approximation, not a result from either paper.

  • Earth: \( \sqrt{0.6/9.81} = 0.25 \) s, so a lean grows fast.
  • Moon: \( \sqrt{0.6/1.62} = 0.61 \) s, about 2.5 times slower, giving you more time to put a foot down (g from the NASA Moon fact sheet).

Calculated in this post with τ = √(h/g), using the example height of 0.6 m for the centre of mass and gravity from NASA and NIST. The ratio of 0.61 s to 0.25 s is about 2.5.

What would the suspension do?

Earth springs would be far too stiff, so the bike would skip over every bump. Static sag is how far the bike settles under its own weight, \(s = mg/k\). Set up for 30 mm of sag on Earth, the same springs give only 5 mm on the Moon.

  1. Earth spring rate. \( k = 250 \times 9.81 / 0.030 = 81{,}750 \) N/m (whole bike, my simplification).
  2. Moon sag with those springs. \( s = 250 \times 1.62 / 81{,}750 = 5 \) mm. The wheels would top out and leave the ground over small rocks.
  3. Moon spring for 30 mm sag. \( k = 13{,}500 \) N/m, six times softer.
  4. Ride frequency. \( f = \frac{1}{2\pi}\sqrt{k/m} \) drops by \(\sqrt{6} = 2.45\), so the bike would wallow slowly over long waves.

That matches the LRV's design: big, soft, flexible wire wheels that deflected about 4.5 cm under load. Sag set-up on Earth is covered in how to set motorcycle suspension sag.

Buzz Aldrin's bootprint pressed into fine grey lunar soil in July 1969
Buzz Aldrin's bootprint from July 1969. Lunar soil is fine, sharp and holds shapes crisply, and it gets into every seal.Photo: NASA / Buzz Aldrin, Public domain, via Wikimedia Commons

Why can't you use rubber tyres?

Because the Moon swings from about 95 K to 390 K, and rubber cannot handle that range. NASA's history of the LRV wheel lists the problems: temperatures of roughly 40 to 400 K across the lunar environment, unfiltered solar radiation, hard vacuum and rolling contact with raw regolith.

  • Lunokhod (1970s): an 800 kg Soviet robot on eight rigid wire-mesh wheels, top speed 2 km/h.
  • MET (Apollo 14): a 75 kg hand-pulled cart on rubber tyres with nitrogen inner tubes, up to 4 km/h. It worked only because it was light and slow.
  • LRV (Apollo 15–17): 210 kg empty, about 700 kg loaded, four driven wheels of woven zinc-coated piano wire with titanium chevron treads, about 16 km/h.

The wire wheel was designed to work at about 20% slip, and climbing a 25° slope was predicted to need around 60% slip on average. On Apollo 15 the crew reported traction good, with about 10% slip.

The Development of Wheels for the Lunar Roving VehicleVivake Asnani, Damon Delap and Colin Creager · NASA/TM-2009-215798, Glenn Research Center · 2009

A history of how General Motors and Bendix competed to build the LRV wheel, reconstructed from archives and interviews with the original engineers. GM's wire-mesh wheel beat Bendix's hoop-spring wheel; it used 50% tread coverage, deflected about 4.5 cm under load, and was rated at 20% slip for best pull. About 500 slope-versus-slip data points implied 59.5% average slip on a 25° slope, so a 0.5 km climb could mean up to 3.2 km of wheel travel. The limit: the authors say the design may not suit future missions needing more traction, load or life.

Read the report (free)

What would the dust do to the bike?

It would sand your seals, blind your radiators and overheat your battery. James Gaier of NASA Glenn reviewed records from all six Apollo landings and sorted dust problems into nine groups, from vision obscuration and false instrument readings to clogged mechanisms, abrasion, failed seals and thermal control.

The Effects of Lunar Dust on EVA Systems During the Apollo MissionsJames R. Gaier · NASA/TM-2005-213610, Glenn Research Center · 2005

A review of mission reports and crew debriefs from Apollo 11 to 17. Simple fixes handled loss of traction, but not clogging, abrasion or lost heat rejection. On Apollo 12, instrument temperatures ran about 68 °F (38 °C) higher than expected, and on Apollo 15 the rover's batteries ran 68 to 78 °F (38 to 43 °C) hot because dust coated their radiators. Lost fender extensions on Apollos 15, 16 and 17 showered crews with dust. The limit: it is a qualitative review, and Gaier warns that ground tests consistently underestimated how bad dust was.

Read the report (free)

Try your own numbers

Use this to check what you just read. Set the gravity to 1.62 for the Moon, 3.73 for Mars or 9.81 for Earth.

Ride on another world

acceleratebrakeEarth: up to 7.85 m/s²Moon: up to 1.30 m/s²same tyre,one-sixth the circle
The friction circle: every mix of braking, accelerating and cornering must fit inside it. On the Moon the circle shrinks to one-sixth of its Earth radius.

So, could you ride a motorcycle on the Moon?

Step by step, the case looks like this:

  • Power: no oxygen, so it must be electric, as the LRV was.
  • Tyres: wire mesh or another airless design, since rubber fails across 95–390 K.
  • Grip: one-sixth of Earth's, so 107 m to stop from 60 km/h; keep speeds near the LRV's 16 km/h (107 m is calculated above).
  • Suspension: springs six times softer than an Earth bike's.
  • Dust: full fenders, sealed bearings and radiators you can keep clean.
Verdict: possible with changes

A lunar motorcycle is possible if it is electric, rides on airless wire or metal-spoke tyres, carries springs about six times softer than on Earth and keeps its speed near 16 km/h, the LRV's sustained top speed. Coulomb friction is the hard limit: grip is μ times weight, so at one-sixth gravity braking from 60 km/h takes about 107 m even with ideal tyres.

It would feel like riding on ice in slow motion: 5-second jumps, lazy wobbles and the same hard landings. For a cost anchor, NASA's May 2026 awards for crewed lunar rover development were about $220 million each.

What if next?

Questions people ask

How fast did the lunar rover go?

NASA Glenn's history of the LRV gives a sustained maximum of about 16 km/h. The 2028 rovers NASA ordered in 2026 are rated at about 10 km/h.

Could you do a wheelie on the Moon?

More easily than you would want. The torque needed to lift the front scales with gravity, just as grip does, so on a hard patch a small throttle input would loft the front, and the bike would then come down 2.5 times more slowly.

Calculated in this post: the tipping time constant √(h/g) is 0.25 s on Earth and 0.61 s on the Moon with the example 0.6 m centre-of-mass height, a ratio of about 2.5. The throttle claim is a physical argument, not a tested result.

Why didn't the lunar rover use rubber tyres?

Lunar surface temperatures run from about 95 K to 390 K, with hard vacuum and solar radiation. Ordinary rubber turns brittle in the cold and degrades in sunlight, so NASA used woven steel wire with titanium treads.

Would a motorcycle engine work on the Moon?

A petrol engine would not, because the Moon has essentially no atmosphere, with a night-time surface pressure of about 3 × 10-15 bar. An electric motor with batteries works, as on the Apollo rovers.

Sources

  1. NASA NSSDC: Moon fact sheet (source for 1.62 m/s², 95–390 K, 3 × 10-15 bar)
  2. Asnani, V., Delap, D. and Creager, C.: The Development of Wheels for the Lunar Roving Vehicle, NASA/TM-2009-215798 (2009) (source for LRV mass, 16 km/h, wire mesh, 4.5 cm deflection, 20% slip, Lunokhod and MET data, 40–400 K)
  3. Gaier, J. R.: The Effects of Lunar Dust on EVA Systems During the Apollo Missions, NASA/TM-2005-213610 (2005) (source for nine dust effects, battery and instrument overheating, 10% slippage on Apollo 15)
  4. Smithsonian National Air and Space Museum: Duct tape auto repair on the Moon (source for the Apollo 17 fender story)
  5. Meijaard, J. P. et al.: Linearized dynamics equations for the balance and steer of a bicycle, Proc. R. Soc. A 463 (2007) (source for the 4.3 m/s weave speed)
  6. Kooijman, J. D. G. et al.: A bicycle can be self-stable without gyroscopic or caster effects, Science 332 (2011) (source for stability near √(gL))
  7. NASA: Update on Moon base rovers, landers and missions (2026) (source for $219–220 million awards)
  8. SpacePolicyOnline: NASA awards initial Moon base rover and lander contracts (2026) (source for 10 km/h, 20° slopes, 200 km range)
  9. European Rubber Journal: Bridgestone to showcase lunar rover tire developments (2026)
Moonlunar gravityfrictionprojectile motionLunar Roving Vehiclelunar dustFroude numberwhat if
Sapta

Sapta (Saptarshi Sarkar) is a mechanical engineer turned marketer in Bengaluru and a solo touring rider. He writes the seven Saptaverse blogs. Work with him or read more of RoadHook Machines.

Keep reading in RoadHook Machines

From the other blogs