Motorcycle suspension sag: how to set preload properly

Preload does not make a spring stiffer. It sets where in its travel the bike rides, and getting that one number right fixes more handling complaints than any damping click.

A Royal Enfield Himalayan 450 adventure motorcycle with long-travel suspension, seen from the side
Photo: Rouv1505, CC BY-SA 4.0, via Wikimedia Commons

Suspension sag is how far a motorcycle's suspension compresses from fully extended under the bike's weight (free sag) and with the rider aboard (rider or static sag). Race Tech's starting points for street bikes are 30-35 mm at the front (28-33% of travel) and 28-37 mm at the rear (28-35%), with 2-17 mm of rear free sag. You set it with the preload adjuster, which moves the ride height without changing spring stiffness.

Key takeaways
  • Street rider sag targets: 28–33% of travel at the front, 28–35% at the rear (Race Tech).
  • Free sag of 2–17 mm on a street bike says the spring rate suits your weight.
  • Preload moves ride height; it does not change the spring rate in F = k·x.
  • Average the L2 and L3 readings to cancel seal and bushing stiction.
  • On a 230 mm travel 390 Adventure R, 30% rear sag is 69 mm.

Most riders touch preload only when a pillion climbs on, and many never measure it at all. Yet sag decides how much travel is left for bumps, how much for the wheel to drop into holes, the bike's rake and trail, and its cornering clearance.

Indian roads, with speed breakers, potholes and sudden broken patches, punish a bike set up wrong more than a smooth European road would. This guide goes past the basics into:

  • the measurement method, with the Race Tech two-reading trick;
  • the maths of springs and preload;
  • what free sag tells you about spring rate;
  • how damping fits on top.
The story

In 1973 Yamaha brought a new rear end to the Motocross World Championship: a single shock absorber in place of the usual pair, the Mono-Shock designed by Lucien Tilkens. Sweden's Håkan Andersson rode it to six Grand Prix wins and the 250 cc world title that season, ahead of Adolf Weil on a Maico and Heikki Mikkola on a Husqvarna. It was the Yamaha factory team's first motocross world championship, and Andersson's long-time mechanic, Eje Skarin, had worked alongside Yamaha's engineers on the bike.

Rivals answered with Honda's Pro-Link, Kawasaki's Uni-Trak and Suzuki's Full-Floater. Rear wheel travel on off-road bikes grew from about 9–10 cm to roughly 30 cm by the end of the 1980s. That tripling is why sag became a number riders must set: the more travel a bike has, the more of it the bike's own weight and the rider's can quietly use up before the first bump.

Wikipedia: Håkan Andersson (motorcyclist), 1973 season; Wikipedia: Monoshock
28-35%street rear sag as a share of travel (Race Tech)
2-17 mmstreet rear free sag, bike only
230 mmfront and rear travel on the KTM 390 Adventure R (2025)
0.624 m/s²average daily vibration on 191 delivery riders, above the EU action value

What is the difference between free sag and rider sag?

Free sag is the compression under the motorcycle's own weight; rider sag (Race Tech calls it static or race sag) is the compression with you on board in riding position, wearing your gear. Rider sag sets the ride height; free sag tells you whether the spring rate suits your weight.

Both are measured from the fully extended position, which is why you need the wheel off the ground for the first measurement. Express each as millimetres and as a percentage of total wheel travel. Percentages matter because a 30 mm sag is about 20% of a KTM 390 Duke's 150 mm of rear travel but only 13% of a 390 Adventure R's 230 mm.

Wheel off groundBike onlyRider on, in gearL1L freeL2, L3Measure axle to a fixed frame point each time. Free sag = L1 − L free. Rider sag = L1 − (L2 + L3) / 2.
Three measurements, same two points. The frame point must be directly above the axle so the tape stays vertical.

How do you measure sag with a tape and a friend?

You need a tape measure, two helpers (one to hold the bike upright, one to read), and a fixed mark on the frame or tail directly above the rear axle. For the fork, measure the exposed chrome from the dust wiper to the bottom triple clamp, or use a zip tie on the fork leg. Race Tech's method averages two readings to cancel seal friction, which is what separates it from the one-number method most riders use.

  1. L1, fully extended. Lift the rear wheel off the ground on a paddock or centre stand until the suspension hangs fully extended. Measure axle centre to the frame mark.
  2. Free sag. Put the bike on its wheels, upright, with no rider. Bounce it gently, let it settle, measure. Free sag = L1 − this reading.
  3. L2, pushed down. Rider on board in normal riding position, feet on the pegs, helper balancing the bike. Push the rear down about 25 mm and let it come up very slowly. Do not bounce. Measure.
  4. L3, lifted up. Lift the rear up and let it settle down very slowly. Measure. L2 and L3 differ because of stiction in seals and bushings.
  5. Calculate. Rider sag = L1 − (L2 + L3) ÷ 2. The true no-friction position lies halfway between L2 and L3.
  6. Adjust preload, repeat. More preload reduces sag; less preload increases it. Change in small steps and measure again.

Sag calculator (Race Tech method)

What sag numbers should you aim for?

Race Tech publishes starting ranges, not rules, and says plainly there are no magic numbers. Use the percentage column for bikes with unusual travel.

Bike typeFront rider sagRear rider sagRear free sag
Street bikes28-33% (30-35 mm)28-35% (28-37 mm)2-17 mm
Road race bikes23-27% (25-30 mm)23-30% (23-32 mm)2-17 mm
Dirt bikes, over 300 mm travel22-25% (65-75 mm)30-35% (95-110 mm)25-50 mm
Dirt 80 cc minis22-25% (55-65 mm)30-35% (75-105 mm)20-40 mm

For a long-travel Indian adventure bike that falls between the street and dirt rows, I would work in percentages. On the 2025 KTM 390 Adventure R's 230 mm of rear travel, 30% is 69 mm. On a Himalayan 450's 200 mm, 30% is 60 mm. Laden touring with luggage usually wants the lower end of the range, so the bike does not ride tail-down and lose steering precision.

230 mmrear travel, KTM 390 Adventure R (2025)
30%sag target in the adventure range
69 mm30% of that 230 mm travel
20-30 kgluggage that can outgrow the spring
Suspension travel on Indian-market motorcycles
See the data as a table
Front travel (mm)Rear travel (mm)
KTM 390 Duke (2023)142150
KTM 390 Duke (2024)150150
RE Himalayan 450200200
KTM 390 Adventure R (2025)230230

Source: KTM and Royal Enfield technical specifications · At 30% rider sag, rear sag would be 45, 45, 60 and 69 mm respectively.

Does preload make the suspension stiffer?

No. Preload compresses the spring before the bike sits on it, so the spring needs more load before it moves further, but its rate in newtons per millimetre is unchanged. Adding preload raises the ride height and reduces sag; the bike feels firmer mainly because it now sits higher in its travel.

The spring maths

A spring obeys F = k·x, where k is its rate and x its compression. With preload x₀, the spring already pushes with k·x₀ at full extension. The suspension only starts to compress when the load exceeds that force, and from then on each extra newton compresses it by 1/k millimetres, exactly as before.

On a linkage monoshock the shock moves less than the wheel, so the wheel rate is the spring rate divided by the square of the motion ratio. That is why a "1 kg/mm" difference in shock spring feels very different on two bikes.

Preload shifts the line, not its slopeSpring forceWheel travel (sag) →Bike + rider loadsag, preloadedsag, no preloadk·x₀Same slope k
Both lines have the same slope, the spring rate k. Preload lifts the starting force to k·x₀, so the same bike-plus-rider load is met at a smaller sag. Stiffness after that point is unchanged.

The practical consequence: preload can bring sag into range, but only spring rate decides how the bike resists a pothole once it is moving.

A rear shock preload adjustment knob on a BMW motorcycle
A remote preload adjuster. Many Indian bikes instead use a stepped collar on the shock body, turned with a C-spanner.Photo: Piero at Dutch Wikipedia, CC BY-SA 3.0, via Wikimedia Commons

What does free sag tell you about your spring?

Free sag is the diagnostic. If you reach the right rider sag but the bike has almost no free sag, so it barely settles under its own weight, you have wound in a lot of preload to hold up a spring that is too soft for you. If you reach the right rider sag but free sag is large, the spring is too stiff and you have backed preload off to get the bike to sag at all.

Rider sagFree sagDiagnosisFix
On targetWithin 2-17 mm (street)Spring suits youFine-tune damping
On targetNear zero; bike topped outSpring too soft, preload crankedStiffer spring
On targetLargeSpring too stiff, preload backed offSofter spring
Too much, even at max preloadAnySpring far too soft for rider plus loadStiffer spring

Riders much heavier or lighter than average, and anyone touring with 20-30 kg of luggage, often discover their spring is outside the adjustable range. A heavier spring or a firmer fork spring with the right oil is the mechanically sound fix.

How do compression and rebound damping fit with sag?

Springs hold the bike up; dampers control how fast it moves. Compression damping resists the suspension being pushed in, rebound damping resists it extending. Damping force depends on how fast the shaft moves, not how far, which is why it is set after sag.

Front wheel and fork of a Ducati 916 SPS sportbike
A front fork and wheel. The fork carries its own spring and damping, and its sag is measured the same way as the rear.Photo: ScuderiaAssindia, CC BY-SA 3.0, via Wikimedia Commons
  • Too little rebound: the bike pogos after a speed breaker and the rear feels loose on a bumpy corner exit.
  • Too much rebound: the suspension "packs down" over a series of bumps, extending too slowly between them, and ends up riding low and harsh.
  • Too much compression: sharp hits feel harsh through the bars and seat.
  • Too little compression: the fork dives hard under braking and bottoms on big potholes.
Springs hold the bike up; dampers control how fast it moves. Set the spring first.

A quick road check for rebound: push down hard on the seat and let go. The tail should return in one smooth movement, with no overshoot above its rest height.

Adjustability varies widely in India. KTM's 2025 390 Adventure R has a 43 mm WP Apex fork with compression and rebound adjustment and a shock with preload adjustment; the Indian Enduro R lists 30-step fork damping and a shock with 20-step damping and 10-step preload.

A Suzuki GSX-R600 rear monoshock absorber removed from the motorcycle, showing the spring and damper body
A sportbike monoshock out of the frame. The coil spring sets sag and ride height; the damper body inside controls how fast it moves.Photo: Andrew Napier, CC BY 2.0, via Wikimedia Commons

What adjustment do Indian motorcycles offer?

Many Indian bikes give you rear preload only; a few premium models add damping adjustment. The table shows travel and published adjustment for bikes whose specs I could open.

MotorcycleFrontRearTravel F / RPublished adjustment
KTM 390 Duke (2023)Telescopic USD forkMonoshock142 / 150 mmSee owner's manual
KTM 390 Duke (2024)USD forkMonoshock150 / 150 mmSee owner's manual
Royal Enfield Himalayan 45043 mm USD forkLinkage monoshock200 / 200 mmSee owner's manual
KTM 390 Adventure R (2025)WP Apex 43 mm USDWP Apex split piston230 / 230 mmFork: compression and rebound; shock: preload
KTM 390 Adventure Enduro R (India, 2025)USD forkMonoshock230 / 230 mmFork: 30-step damping; shock: 20-step damping, 10-step preload

Does suspension setup affect rider fatigue?

It plausibly does, and vibration exposure on two-wheelers is already high. A 2025 study measured whole-body vibration at the seat for 191 food delivery riders in eastern Peninsular Malaysia using a tri-axial seat-pad accelerometer to ISO 2631-1. Their average daily exposure, A(8), was 0.624 m/s², above the exposure action value in EU Directive 2002/44/EC; three riders exceeded the exposure limit value. Whether the motorcycle's suspension had been serviced came out as one of three significant predictors of high exposure, alongside working days per week and existing musculoskeletal problems.

191delivery riders measured in Malaysia, 2025
0.624 m/s²mean daily whole-body vibration exposure, A(8)

For long-distance riders the lesson is simple: a correctly sprung, freshly serviced suspension is a comfort and fatigue item, not just a performance one. Fork oil degrades, seals wear and linkage bearings dry out, all of which widen the L2-L3 stiction gap the calculator shows.

How does sag change the bike's steering?

Sag sets the bike's attitude, and attitude sets rake and trail. Too little rear sag (too much preload) lifts the tail, steepens rake and quickens steering; too much rear sag under luggage slackens it. The geometry is worked through in rake and trail explained with real bike numbers, and how lean and steering interact in countersteering explained. Sag also eats into ground clearance, a key number in the ground clearance ranking. For a used bike, a big stiction gap is a check worth adding to the used bike checklist, and before a long ride, the daily distance planner shows why comfort over 500 km matters.

Research behind this post

Whole-body vibration exposure and its predictors among food delivery riders in eastern Peninsular MalaysiaAziah Daud et al. · Journal of Public Health Research · 2025

A cross-sectional study of 191 food delivery riders measured seat vibration with a Larson Davis HVM 100 and tri-axial seat pad following ISO 2631-1. Mean daily exposure A(8) was 0.624 m/s² (SD 0.317), above the EU 2002/44/EC action value, with three riders over the limit value. Predictors of exposure above the action value were more working days (aOR 1.56), existing musculoskeletal disorders (aOR 2.93) and the motorcycle's suspension service status (aOR 0.39). The limit: delivery riding in one region, and the abstract does not separate suspension setup from bike age or road quality.

Read the paper (free)
Estimating Motorcycle Telescopic Fork Suspension Travel Speed with Four-Degree-of-Freedom Full-Vehicle Kalman FilterAndrea Ponso, S. Pakštys, Angelo Bonfitto · Sensors · 2026

Semi-active suspensions set damping from fork speed, which is hard to measure directly. The authors estimated fork elongation speed from two simulated accelerometers using a full-motorcycle Kalman filter. Error was 6.54% on the smoothest ISO road class A and 7.07% on the roughest class H, against 57.46% and 94.47% for a simpler single-corner model. The limit: simulation with synthetic sensor data, not road tests, but it shows why damping is a speed problem.

Read the paper (free)
Advances in the Modelling of Motorcycle DynamicsR.S. Sharp, S. Evangelou, D.J.N. Limebeer · Multibody System Dynamics · 2004

Besides tyre and frame modelling, this Imperial College paper gives a new analytic treatment of the linkage monoshock rear suspension, using measured parts of a Suzuki GSX-R1000. It shows how the linkage changes the relation between shock and wheel movement and how frame and rider properties affect weave and wobble. The limit: a superbike, with some frame parameters estimated.

Read the paper (free)

Questions people ask

How much should I change preload for a pillion?

Measure, then add preload until rider sag with both of you aboard returns to roughly the same percentage of travel as when solo. If maximum preload still leaves too much sag, the spring is too soft for two-up touring.

Can I set sag alone?

Not accurately. Someone has to hold the bike upright while you sit in riding position, and a third person reading the tape helps. Leaning against a wall changes the load on the suspension.

Why does my bike feel harsh even with correct sag?

Correct sag with harshness usually points to too much compression damping, an overly stiff spring (check free sag), old fork oil or worn bushings. A large gap between L2 and L3 in the calculator suggests friction in seals and linkage.

Should front and rear sag be the same?

As percentages they are usually close; Race Tech's street front range is 28-33% and rear 28-35%. Keeping them balanced holds the designed rake and trail.

Sources

  1. Race Tech: Frequently asked questions, static sag method and sag table
  2. Daud et al., J. Public Health Research: Whole-body vibration exposure among food delivery riders (2025)
  3. Ponso et al., Sensors: Estimating motorcycle fork travel speed with a Kalman filter (2026)
  4. Sharp, Evangelou, Limebeer: Advances in the modelling of motorcycle dynamics (2004)
  5. EU Directive 2002/44/EC on exposure to vibration (2002)
  6. KTM: 2025 390 Adventure R technical specifications
  7. KTM: 2024 390 Duke technical specifications
  8. KTM: 2023 390 Duke technical specifications
  9. Royal Enfield: Himalayan 450 technical specifications
  10. Autocar Professional: KTM launches updated 390 Adventure X and Enduro R (2025)
  11. Wikipedia: Håkan Andersson (motorcyclist), 1973 250 cc title on the Yamaha Mono-Shock
  12. Wikipedia: Monoshock (Tilkens design, rival systems, travel growth)
preloadrider sagfree sagrebound dampingcompression dampingmonoshockKTM 390 AdventureHimalayan 450
Sapta

Sapta (Saptarshi Sarkar) is a mechanical engineer turned marketer in Bengaluru and a solo touring rider. He writes the seven Saptaverse blogs. Work with him or read more of RoadHook Machines.

Keep reading in RoadHook Machines

From the other blogs