What if motorcycles were invented today, not in 1885?

Design a motorcycle from a blank sheet in 2026 and the city bike comes out electric, with a chain, two wheels and air in its tyres. The 400 km tourer still doesn't, because its battery would weigh about 240 kg.

A replica of the 1885 Daimler Reitwagen, a wooden-framed motorcycle with outrigger wheels
Photo: Levin Holtkamp, CC BY-SA 4.0, via Wikimedia Commons

If engineers designed the motorcycle from scratch today, the commuter would almost certainly be electric: at city speeds it needs only about 26 Wh per km, so a 4 kWh battery covers a week of riding. The chain, two wheels, pneumatic tyres and handlebar would survive on merit. The long-range tourer is the exception: matching a 12-litre petrol tank's 420 km at 100 km/h needs about 38 kWh, roughly 240 kg of battery with today's packs.

Key takeaways
  • 46.4 MJ/kg for petrol against about 0.9 MJ/kg for the best lithium-ion cells: a 50-fold gap.
  • 26 Wh/km at 40 km/h but 91 Wh/km at 100 km/h, because drag power grows with speed cubed.
  • 97% fall in lithium-ion cell prices since 1991, per Ziegler and Trancik at MIT.
  • 98.6%: a chain drive's best measured efficiency, which is why it would be reinvented.
  • Lock-in, not merit, explains much of why the 1885 layout is still with us.

Every motorcycle on Indian roads carries decisions made for a world of iron tyres, gas lamps and no petrol pumps. The fuel tank sits between your knees because that was the highest dry spot in 1900. A cable clutch exists because early engines couldn't idle in gear.

So here is a fair test. Hand a team of 2026 engineers today's batteries, motors, materials and roads, and no memory of the last 140 years. What do they build? And which of the old ideas do they rediscover anyway?

What did the first motorcycle look like?

The first was the Daimler Reitwagen, a wooden "riding car" patented on 29 August 1885. It had a 264 cc single-cylinder four-stroke making about 0.37 kW (0.5 hp) at 600 rpm, iron-tyred wooden wheels, and spring-loaded outrigger wheels to stop it falling over. It weighed 90 kg and did about 11 km/h.

The story

Nine years after the Reitwagen, someone tried to sell the idea. On 20 January 1894 the brothers Heinrich and Wilhelm Hildebrand, former steam-engine engineers, and Alois Wolfmüller received German patent No. 78553 for the motorcycle they built in Munich. It had a 1,489 cc water-cooled two-cylinder four-stroke making 2.5 bhp at 240 rpm, hot-tube ignition, and connecting rods that drove the rear wheel directly. It had no clutch and no pedals: you ran beside it and jumped on. It weighed about 50 kg and topped out near 45 km/h.

About 2,000 were built, and Duncan and Superbie made it under licence in Paris. But the price was high, better designs arrived quickly, and production stopped in 1897. The first motorcycle built for sale was shaped, like the Reitwagen, by its engine.

Wikipedia: Hildebrand & Wolfmüller

Notice the Reitwagen's job. Daimler wanted a light test bed for his engine, and two wheels were the cheapest chassis around. The motorcycle was born as an engine on a bicycle frame, and its layout followed the engine from then on. For the fuller history, see the Reitwagen story.

An 1894 Hildebrand and Wolfmüller motorcycle in the National Technical Museum in Prague
An 1894 Hildebrand & Wolfmüller in Prague's National Technical Museum, one of the earliest motorcycles built for sale. The engine still dictates the whole layout.Photo: Addvisor, CC BY-SA 4.0, via Wikimedia Commons

Why would a 2026 design team start with electric?

Because at city speeds a motorcycle needs very little energy, and electric drivetrains waste very little of it. The awkward number, energy per kilogram, only bites when you need a lot of energy.

Assumptions

  • Bike 210 kg plus 75 kg rider: 285 kg in all.
  • Drag area 0.50 m², the upright-rider value measured in a University of Warwick wind tunnel.
  • Rolling resistance coefficient 0.015 and 85% battery-to-wheel efficiency (my estimates).
  • Sea-level air at 1.225 kg/m³, flat road, steady speed.

The worked solution

  1. Power at the wheel. Drag plus rolling resistance:
    \[ P = \tfrac{1}{2}\rho\, C_dA\, v^3 + C_{rr}\, m g\, v \]
  2. City, 40 km/h (11.1 m/s). Drag: \( 0.306 \times 11.1^3 = 420 \) W. Rolling: \( 0.015 \times 285 \times 9.81 \times 11.1 = 466 \) W. Total 886 W (calculated from the assumptions above and the drag-power formula).
  3. Energy per km. Divide power by speed and convert:
    \[ \frac{886\ \text{W}}{11.1\ \text{m/s}} = 79.7\ \text{J/m} = 22.1\ \text{Wh/km} \;\Rightarrow\; \frac{22.1}{0.85} = 26\ \text{Wh/km from the battery} \]
  4. Highway, 100 km/h (27.8 m/s). Drag: \( 0.306 \times 27.8^3 = 6{,}564 \) W. Rolling: 1,165 W. Total 7,729 W, or 77.3 Wh/km at the wheel and 91 Wh/km from the battery (same drag-power formula and assumptions).
  5. Battery for a 420 km tourer. The NS200's 12-litre tank gives about 420 km at 35 km/l (an assumed highway mileage):
    \[ E = 420\ \text{km} \times 91\ \text{Wh/km} = 38.2\ \text{kWh} \;\Rightarrow\; m_{pack} = \frac{38{,}200}{160\ \text{Wh/kg}} \approx 240\ \text{kg} \]
    The 160 Wh/kg pack figure is my estimate: cells reached over 250 Wh/kg by 2018, and casing, cooling and wiring add weight.
  6. Compare the petrol tank. 12 litres of petrol weighs about 9 kg and holds \( 12 \times 34.2 = 410 \) MJ (34.2 MJ/L for petrol, Wikipedia: Energy density), or 114 kWh of chemical energy.

The commuter case is easy: 26 Wh/km means a 50 km day uses 1.3 kWh. The tourer is not: a 240 kg pack would more than double the bike's weight, and that extra mass raises rolling resistance, which needs more battery. Speed, not distance, is what kills the electric tourer, because energy per km rises roughly with speed squared.

Calculated in this post from the 26 Wh/km above: 26 Wh/km × 50 km = 1.3 kWh. With these example inputs, the 26 Wh/km comes from the assumptions listed above, with the drag area from the University of Warwick wind-tunnel study.

Battery energy needed per km at steady speed (285 kg, CdA 0.50)
See the data as a table
From the battery (Wh/km)
40 km/h26.0
60 km/h41.5
80 km/h63.1
100 km/h90.9
120 km/h124.9

Source: My calculation using the drag equation and the University of Warwick upright-rider CdA; rolling resistance and efficiency are stated estimates · Flat road, no wind, no stops. Real riding with acceleration and braking uses more; regenerative braking recovers some.

Steady speedBattery Wh/kmRange on 3.91 kWhRange on 10.3 kWhBattery for 420 km
40 km/h26150 km396 km11 kWh, ~68 kg
60 km/h4294 km248 km17 kWh, ~109 kg
80 km/h6362 km163 km27 kWh, ~166 kg
100 km/h9143 km113 km38 kWh, ~240 kg
120 km/h12531 km82 km52 kWh, ~328 kg

The 3.91 kWh pack is the Royal Enfield Flying Flea C6's, and 10.3 kWh is the Ultraviolette F77 Mach 2 Recon's. Their claimed IDC ranges, 154 km and 323 km, sit close to my 40 km/h column, because the Indian Driving Cycle is a gentle, mostly low-speed test.

An 18650 and a slightly larger 21700 cylindrical lithium-ion cell side by side
An 18650 and a 21700 cylindrical lithium-ion cell. Ziegler and Trancik found cylindrical cells tend to post the highest energy per kilogram each year.Photo: Sevenethics, CC0, via Wikimedia Commons

How big is the gap between petrol and a battery?

About 50 times by weight, which shrinks to roughly 27 times at pack level once you count what each drivetrain wastes. Petrol stores 46.4 MJ/kg; good lithium-ion cells store up to about 0.9 MJ/kg (250 Wh/kg).

Calculated in this post from petrol's 46.4 MJ/kg (Wikipedia: Energy density) and about 250 Wh/kg for the best lithium-ion cells (Ziegler and Trancik, 2021); the efficiency-adjusted ratio is worked out below.

Then efficiency closes part of the gap. My NS200-style example burns 271 Wh of petrol per km at 100 km/h (34.2 MJ/L divided by 35 km/l) to deliver 77 Wh at the wheel, about 28%. The electric bike delivers about 85%. So:

Calculated in this post from petrol's 34.2 MJ/L (Wikipedia: Energy density), an assumed 35 km/l highway mileage and the 77 Wh/km at the wheel worked out above: 34.2 MJ/L ÷ 35 km/l = 0.977 MJ/km = 271 Wh/km; 77 ÷ 271 = 28%.

\[ \frac{12.9\ \text{kWh/kg} \times 0.28}{0.16\ \text{kWh/kg} \times 0.85} \approx \frac{3.6}{0.136} \approx 27 \]

At pack level, petrol still carries about 27 times more useful energy per kilogram. That single ratio decides which bikes go electric first.

Useful energy at the wheel, per kg carriedPetrol: 12.9 kWh/kg × 28% efficient3.6 kWh per kgBattery pack: 0.16 kWh/kg × 85% efficient0.14 kWh per kgFor 420 km at 100 km/h:Petrol: about 9 kg of fuel (12 litres)Battery: about 240 kg of pack (38 kWh)Bars to scale. Pack figure is an estimate.
Even after counting the electric drivetrain's three-times-better efficiency, petrol delivers about 27 times more useful energy per kilogram. My calculation from published energy densities.

Which 1885 ideas would a clean-sheet team keep?

More than you might think. Several parts of the old layout are not habits; they are the best answer physics allows.

IdeaKept today?Why
Two wheels in lineYesNarrow footprint and lean-to-turn; the frontal area stays small, so drag stays low
Chain final driveYes, or a beltA Johns Hopkins test measured 81–98.6% efficiency, hard to beat at this weight and cost
Air-filled tyreYesCarries load on air, absorbs bumps and keeps a broad contact patch
Handlebar steeringYesCountersteering is physics, not tradition
Multi-speed gearbox and clutchNoAn electric motor makes torque from zero rpm; one fixed ratio covers the range
Fuel tank between the kneesNoThe heaviest part, the battery, goes as low as possible for handling

The chain is the most interesting survivor. The Johns Hopkins team, testing for Shimano, found that lubrication made no measurable difference in the lab. Its outdoor job is keeping grit out, which is why the chain cleaning guide matters more than the brand of lube.

Petrol layout (inherited)fuel tankengine+ gearboxClutch, 6 gears, exhaust,radiator, oil pumpMass high, at the tankClean-sheet electric layoutbattery, lowmotorOne fixed ratio, chain or beltNo clutch, no exhaustMass low, between the wheels
What changes and what stays. Wheels, steering and the final drive survive; the tank, clutch and gearbox go, and the heaviest part drops to the bottom of the frame. A schematic, not to scale.

If electric is better for cities, why are most bikes still petrol?

Because technologies lock in. The economist W. Brian Arthur showed in 1989 that when a technology gets better the more people use it, early chance events can make one option win for good, even if a better one turns up later. His examples were the QWERTY keyboard and VHS tape.

Motorcycles fit the model closely:

  • Fuel stations exist because petrol bikes exist, and petrol bikes sell because fuel stations exist.
  • Mechanics and spares in every Indian town know carburettors and chains, not battery management systems.
  • Resale value is easy to judge for a petrol bike and hard for a five-year-old battery.

A team starting in 2026 would face none of that history. That is the real meaning of this what-if: strip out lock-in and the city motorcycle goes electric at once. In the real world, India's electric two-wheeler sales reached about 13.5 lakh high-speed units in 2025.

A LiveWire electric motorcycle on a mountain road
A LiveWire electric motorcycle. The Warwick wind tunnel measured this family at 0.569 m² of drag area with an upright rider, almost exactly the value used above.Photo: Robertedwardkroll, CC0, via Wikimedia Commons
Verdict: possible with changes

A motorcycle invented in 2026 would be electric for the city and for rides of up to about 150 km at moderate speed: at 26 Wh/km a 4 kWh pack is plenty. It would keep two wheels, a chain or belt, air-filled tyres and handlebars, because those are the physics-optimal answers. The long-range tourer is the part that doesn't change yet: 420 km at 100 km/h needs about 38 kWh, around 240 kg of pack. The law that decides it is the drag-power law, \( P \propto v^3 \), meeting petrol's 50-fold advantage in energy per kilogram.

How sensitive is this to the assumptions?

  • Better packs. At 300 Wh/kg pack level, the 420 km tourer's battery falls from 240 to about 127 kg. Still heavy, but now comparable to adding a pillion.
  • Slower touring. At 80 km/h instead of 100, the same trip needs 27 kWh, a 30% cut, because energy per km scales with speed squared at highway speeds.
  • Fairing. A tucked rider or full fairing cutting drag area to 0.35 m² trims the 100 km/h figure from 91 to about 68 Wh/km.
  • Cheaper cells. Ziegler and Trancik estimate real cell prices fell 13% a year from 1992 to 2016. Cost was the old objection; for a commuter, it is mostly gone.

Where the model breaks: it assumes steady speed. Real city riding wastes energy in stop-start braking, and electric bikes win back part of it with regenerative braking, which a petrol bike can't. That makes the city case even stronger than my numbers show.

Use this to check what you just read. Plug in your own daily ride.

How big a battery would your ride need?

The motorcycle was born as an engine looking for a chassis. Invent it today and it becomes a chassis looking for a battery.The working above

What does the research say?

Re-examining rates of lithium-ion battery technology improvement and cost declineMicah S. Ziegler, Jessika E. Trancik · Energy & Environmental Science (arXiv preprint) · 2021

The MIT authors assembled and harmonised price, market, patent and performance data for lithium-ion cells. They find real price per kWh fell about 97% from 1991, or 13% a year from 1992 to 2016; counting energy density and specific energy raises the improvement rate to 17% a year. Specific energy rose from about 80 to over 250 Wh/kg between 1991 and 2018. Limit: cell-level data, so pack weight and cost are higher.

Read the paper (free)
Fuel consumption reduction technologies for the two-wheeler fleet in IndiaSunitha Anup, Ashok Deo, Anup Bandivadekar · International Council on Clean Transportation white paper · 2021

The ICCT assessed fuel-saving technology packages for small motorcycles, large motorcycles and scooters in India, and compared their cost-effectiveness with electric two-wheelers modelled at 100 km range for a small motorcycle and 75 km for a scooter. It notes India's two-wheeler fleet burns more petrol than all other road transport combined, and estimates hybrids cut fuel use by about 9–11%. Limit: costs are projections to 2025–2030.

Read the paper (free)
Effects of frictional loss on bicycle chain drive efficiencyJames B. Spicer et al. · Johns Hopkins University, reported by ScienceDaily · 1999

On a computer-controlled rig, the team measured chain-drive efficiency between 81% and 98.6% depending on sprocket size and chain tension; higher tension gave higher efficiency, and removing lubricant made no measurable lab difference. Limit: bicycle chains at bicycle loads, not motorcycle chains at 30 kW.

Read the summary (free)

For more on the electric side, see LFP vs NMC batteries and why electric motorcycles are slow to catch on in India. The Yantra page collects the rest of the engineering work on this site.

What if next?

Questions people ask

When was the first motorcycle invented?

The Daimler Reitwagen was patented on 29 August 1885 and first ridden by Paul Daimler in November 1885. It had a 264 cc engine making about 0.5 hp and reached roughly 11 km/h.

Why do electric motorcycles have short highway range?

Because the power needed to push through air rises with speed cubed. At 100 km/h a typical bike and rider need about 91 Wh per km from the battery, three and a half times the 26 Wh/km needed at 40 km/h.

Do electric motorcycles need a gearbox?

Usually not. An electric motor produces strong torque from standstill across a wide speed range, so most use a single fixed reduction to the rear wheel through a chain or belt.

How much heavier is a battery than a fuel tank?

For the same useful energy at the wheel, a pack is roughly 27 times heavier than petrol, by my calculation. A 12-litre tank of petrol weighs about 9 kg; the battery for the same 420 km at 100 km/h would weigh about 240 kg.

Sources

  1. Wikipedia: Daimler Reitwagen (source for the patent date, 264 cc, 0.37 kW, 11 km/h, 90 kg and the 1903 fire)
  2. Wikipedia: Hildebrand & Wolfmüller (1894 patent, 1,489 cc, 2.5 bhp, about 2,000 built, 1897; the story)
  3. Wikipedia: Paul Daimler (source for the 10 November date variant)
  4. Ziegler and Trancik: Re-examining rates of lithium-ion battery technology improvement and cost decline (2021) (source for the 97% price fall and 80 to 250+ Wh/kg)
  5. Wikipedia: Energy density tables (source for petrol 46.4 MJ/kg and 34.2 MJ/L)
  6. Kirca and McGordon: Effect of rider position on the energy consumption of an electric motorcycle (2024) (source for 0.50 m² and the LiveWire's 0.569 m²)
  7. Bajaj Auto: Pulsar NS200 owner's manual (source for the 12-litre tank)
  8. ICCT: Fuel consumption reduction technologies for the two-wheeler fleet in India (2021)
  9. ScienceDaily: Johns Hopkins study of bicycle chain efficiency (1999) (source for 81–98.6%)
  10. JASSS: Summary of Arthur's 1989 model of competing technologies (source for the lock-in model and QWERTY/VHS examples)
  11. Autocar India: Ultraviolette F77 Mach 2 specifications (source for 10.3 kWh, 323 km, 207 kg)
  12. Electrek: Royal Enfield Flying Flea C6 launch (2026) (source for 3.91 kWh, 154 km, 124 kg)
  13. EVreporter: India's EV market, CY 2025 annual insights (2026) (source for 13,45,244 e-2W units)
Daimler Reitwagenelectric motorcycleenergy densitylock-inpath dependencebatterychain drivewhat if
Sapta

Sapta (Saptarshi Sarkar) is a mechanical engineer turned marketer in Bengaluru and a solo touring rider. He writes the seven Saptaverse blogs. Work with him or read more of RoadHook Machines.

Keep reading in RoadHook Machines

From the other blogs