If you rode in first gear the whole way from Bengaluru to Mysuru, a modern 390 cc single would carry you at about 45 to 50 km/h with the engine screaming at 8,000 to 9,000 rpm, the trip would take about two and a half hours instead of one and a half, and you would burn roughly 40% more fuel than a sensible gear at a sensible speed. The engine would almost certainly survive, because it is built to run at those revs; your ears, your wrists and your fuel bill would not enjoy it.
- 21.33 : 1 is the overall first-gear reduction on 390 Duke gearing, so first tops out near 55 km/h at 10,000 rpm.
- 2 h 37 min of riding for 118 km at 45 km/h, against about 1 h 29 min at 80 km/h.
- ~1.29 million crankshaft revolutions in first, about 3.2 times a sixth-gear run.
- ~40% more fuel: roughly 24 km/l in first against about 34 km/l at 80 km/h in sixth (model estimate).
- Friction is the culprit: in first it takes more than three times the power that actually moves the bike.
It is a silly question with a serious engine inside it. Gear ratios, engine friction and road load are the three things that decide how a motorcycle uses fuel, and holding one gear for 118 km isolates them neatly.
The working below uses the published gearing of the KTM 390 Duke, the engine family behind Sapta's 2026 KTM 390 Adventure X Plus, and checks the answer against a real number from his own ride log.
How fast can a bike go in first gear?
A typical 390 cc motorcycle tops out at about 50 to 58 km/h in first gear, because first is a deep reduction of about 21 to 1 between the crankshaft and the rear wheel. The 2013-14 KTM 390 Duke's published gearing on moto-data gives every stage as tooth counts:
The gear train, stage by stage
| Stage | Teeth | Ratio |
|---|---|---|
| Primary drive (crank to clutch) | 30 : 80 | 2.667 |
| First gear | 12 : 32 | 2.667 |
| Sixth gear | 25 : 21 | 0.840 |
| Final drive (sprockets) | 15 : 45 | 3.000 |
| Overall, first gear | - | 21.33 |
| Overall, sixth gear | - | 6.72 |
The 390 Adventure shares the 30:80 primary and 15:45 final drive on the same database; its individual gear ratios are not listed there, so the Duke's are used as the stand-in. Here is the working.
- Overall ratio. Multiply the stages:
\[ i_1 = \frac{80}{30} \times \frac{32}{12} \times \frac{45}{15} = 2.667 \times 2.667 \times 3 = 21.33 \]
- Rolling circumference. A 150/70-17 tyre has a 105 mm sidewall on a 431.8 mm rim, so its diameter is 641.8 mm. Allowing about 3% for the tyre squashing under load, the rolling circumference (rear tyre as listed on moto-data.net) is \( C = \pi \times 0.6418 \times 0.97 \approx 1.956 \) m.
- Road speed. At engine speed \( n \) in rpm:
\[ v = \frac{n}{i}\, C \times \frac{60}{1000}\ \text{km/h} = \frac{10{,}000}{21.33} \times 1.956 \times 0.06 \approx 55\ \text{km/h} \]
- Check sixth. The same 10,000 rpm in sixth would be \( 10{,}000 / 6.72 \times 1.956 \times 0.06 \approx 175 \) km/h on paper. Real bikes run out of power before that, so the ratio is not the limit in top gear; it is the limit in first.
Bajaj's own NS200 manual shows how the factory thinks about this: its shift light blinks between 10,000 and 10,500 rpm and stays on above 10,500. Revving to that light in first is allowed; staying there for 118 km is the question.
Can an engine hold high revs for hours?
It has been done in public, on a track, with a single-cylinder engine far older than the KTM's.
On 18 March 1961, a factory-prepared Velocette Venom Clubman, a 500 cc single with a fairing, rolled onto the Montlhéry oval near Paris. The 2.7 km concrete bowl was bumpy and badly lit at night. A team of six French riders, joined by Motor Cycling journalist Bruce Main-Smith, took turns in the saddle. They stopped only to swap riders and refuel, pouring petrol from a bucket through a funnel. The bike first took the 12-hour record at more than 104 mph (167 km/h), then kept going. After 24 hours it had averaged 100.05 mph (161 km/h), the first motorcycle of any size to top 100 mph for a full day. That single kept its engine spinning hard for 24 hours; our KTM would need about 2.6 hours below peak-power revs.
Wikipedia: Velocette Venom, the 1961 Montlhéry 24-hour recordSee the data as a table
| First gear (21.33:1) (km/h) | Sixth gear (6.72:1) (km/h) | |
|---|---|---|
| 6,000 rpm | 33.0 | 104.8 |
| 7,000 | 38.5 | 122.2 |
| 8,000 | 44.0 | 139.7 |
| 9,000 | 49.5 | 157.2 |
| 9,500 | 52.3 | 165.9 |
| 10,000 | 55.0 | 174.6 |
| 10,500 | 57.8 | 183.4 |
Source: Calculated from KTM 390 Duke 2013-14 gearing (moto-data.net) and a 150/70-17 rear tyre · Sixth-gear values above about 150 km/h are geometric only; the bike lacks the power to reach them.
How long would the ride take in first gear?
At a steady 45 km/h, 118 km takes 2 hours 37 minutes of riding, against about 1 hour 29 minutes at 80 km/h. The expressway length is the fair benchmark because the service roads and NH-275 run alongside it; your door-to-door distance will be longer at both ends. The interesting number is not time but revolutions:
Calculated in this post from the 118 km expressway length divided by two steady speeds, 45 and 80 km/h, which are this scenario's assumptions.
At 45 km/h in first the engine turns 8,181 rpm; at 80 km/h in sixth it turns 4,581 rpm for 89 minutes, or about 0.41 million revolutions. The first-gear trip asks every bearing, cam lobe and piston ring for 3.2 times as many cycles to cover the same road.
Calculated in this post from the 390 Duke gearing on moto-data.net (overall ratios 21.33 and 6.72) and the 1.956 m rolling circumference worked out above.

How much more fuel does first gear burn?
First gear burns roughly 40% more fuel per kilometre than a high gear at a moderate speed, and well over twice as much as a high gear at the same 45 km/h, because the engine spends most of its fuel fighting its own friction at high revs.
The model: a Willans-line budget
The model is the Willans-line idea engineers use for engines at part load: the fuel power has to cover the road load plus the engine's internal friction, divided by how efficiently the combustion turns fuel into work.
Assumptions, stated plainly:
- Bike plus rider 230 kg, rolling resistance coefficient 0.015, drag area \( C_dA = 0.6 \) m², air density 1.2 kg/m³. These are typical values, my estimates.
- Displacement \( V_d = 373 \) cm³ for the 390 Duke engine; the four-stroke fires once every two revolutions, hence the 2 in the formula.
- Friction mean effective pressure (fmep) rises with rpm. I assume 0.9 bar at 2,600 rpm, 1.1 bar at 4,600 rpm and 1.5 bar at 8,200 rpm, a plausible range for a small single, not a measured map.
- Indicated efficiency \( \eta_i = 30\% \), petrol at 32 MJ per litre (US DOE fuel properties table).
| Case | Engine speed | Road load | Friction | Fuel power | Estimate |
|---|---|---|---|---|---|
| 45 km/h, first gear | 8,181 rpm | 1.13 kW | 3.82 kW | 16.5 kW | ~24 km/l |
| 45 km/h, sixth gear | 2,577 rpm | 1.13 kW | 0.72 kW | 6.2 kW | ~65 km/l (too optimistic) |
| 80 km/h, sixth gear | 4,581 rpm | 4.70 kW | 1.57 kW | 20.9 kW | ~34 km/l |
The sixth-gear figure at 45 km/h is too rosy, because at that whisper of throttle the engine also loses a lot to pumping air past a nearly closed throttle, which the simple model ignores. The first-gear row is the robust one: friction alone is more than three times the road load in first gear.
A real-world anchor
On his early-November 2026 Bengaluru–Mulbagal run, Sapta's KTM 390 Adventure X Plus returned 26.5 km/l at 100 to 120 km/h on Shell V-Power. A bike doing 24 km/l while crawling at 45 km/h is using more fuel per kilometre than one doing twice the speed in top gear.
Use this to check what you just read with your own bike's numbers.
Your first-gear trip to Mysuru
The authors built a bottom-up energy budget for an average passenger car, splitting fuel energy into exhaust, cooling and the friction in the engine, transmission, tyres and brakes, then scaled it to the world fleet. About a third of fuel energy goes to overcoming friction, 28% if braking is excluded, and only 21.5% actually moves the car. That friction cost 208,000 million litres of fuel worldwide in 2009, about 340 litres per car per year. The limit: it is an average car in average driving, not a motorcycle held at high revs, where the friction share is higher still.
Read the paper (free)Would the engine be damaged by 118 km at 8,000 rpm?
A healthy, well-oiled modern engine would not be damaged by 118 km at 8,000 to 9,000 rpm, because that is below its peak-power speed and well inside the range it was designed to sustain.
The 390 Duke engine makes its rated 32 kW at 9,500 rpm by the published figures, so the first-gear trip never even reaches peak-power revs. Where the cost shows up is wear and heat:
- Wear scales with revolutions and sliding distance. Archard's wear law says worn volume grows with load times sliding distance. Three times the revolutions means roughly three times the ring and cam sliding distance for the trip, at light load. On a well-lubricated engine, that is still a tiny fraction of its life.
- Mean piston speed stays sane. For the NS200's 49 mm stroke (Bajaj manual), \( \bar v_p = 2 S n / 60 = 2 \times 0.049 \times 9{,}000 / 60 = 14.7 \) m/s, a normal figure for road engines at high revs.
- Heat goes into the coolant, not the road. At 45 km/h the radiator sees little airflow while the engine rejects friction heat continuously, so the fan would cycle often, especially in traffic.
- Oil takes the abuse. Sustained high revs shear the oil and heat it; the oil change after such a trip would be money well spent. See the oil change guide.
The real risk is the rider
The real risk is not the engine but the rider. Engine braking in first is fierce, so every throttle roll-off becomes a sharp deceleration that a car behind does not expect; the physics of that is in is engine braking bad for your bike.
- Vibration at constant high rpm numbs hands within the first hour.
- Noise: a single's exhaust note at 8,000 rpm for two and a half hours is its own kind of fatigue.
- Speed gap: at that crawl, almost everything on the old NH-275 is closing on you from behind.
A review and update of the 2012 car study, setting friction against world energy use of about 400 exajoules a year. It estimates that friction consumes roughly a fifth of all energy used worldwide and a third of the energy used in transport, and that better materials, lubricants and designs could cut friction and wear losses by 18-40%, worth up to 8.7% of global energy use. It also shows battery-electric cars lose about half as much energy to friction as combustion cars. The limit: these are fleet-level estimates built on models, not engine-by-engine measurements.
Read the paper (free)Why does a higher gear save fuel at the same speed?
A higher gear saves fuel because it lets the engine make the same road power at lower revs and wider throttle, where friction and pumping losses take a smaller share. Power is torque times angular speed, \( P = T\,\omega \), and the road needs the same power at 45 km/h whatever the gear.
| At 45 km/h | First gear | Sixth gear |
|---|---|---|
| Engine speed | 8,181 rpm | 2,577 rpm |
| How power is made | Low torque, high \( \omega \) | Higher torque, low \( \omega \) |
| Throttle | Nearly closed, high pumping loss | Wider open, lower pumping loss |
| Friction power (model) | 3.82 kW | 0.72 kW |
In first gear the engine pays friction on every one of the extra revolutions, and gets nothing for them.
In sixth, the same power comes from higher torque at low revs, so the engine runs closer to its efficient zone. The same logic explains why changing sprockets shifts fuel economy as well as acceleration, and why power and torque are two views of one curve.

So, can you ride first gear all the way?
Riding first gear from Bengaluru to Mysuru is entirely possible for a modern liquid-cooled bike. The bill, by the estimates above:
- About an hour of extra riding time;
- roughly 1.4 extra litres of petrol for 118 km (about ₹160 at June 2026 Bengaluru prices);
- three times the engine revolutions, with an oil change worth doing afterwards.
The engine's design limit is the rev limiter, and first gear at 45 km/h, about 8,200 rpm, stays under it and under the 9,500 rpm peak-power speed. The deciding number is friction: about 3.8 kW of it in first against 0.7 kW in sixth at the same speed.
More gear for the road is on the gear page.
What's new
- Bengaluru petrol rises to ₹111.68 a litre, the sharpest increase among metros that day HDFC Sky, June 2026
- Updated Pulsar NS200 gets ride-by-wire, traction control and a quickshifter that makes gear choice easier DriveSpark, Oct 2026
- NHAI's two-wheeler ban on the Bengaluru–Mysuru Expressway, still the rule for bikes on this route Outlook India, July 2023, updated Jan 2024
What if next?
- What if your bike had square wheels? A perfectly smooth ride, on a road of upside-down hanging chains.
- Could a motorcycle run on chai? A litre of chai holds about one-fifteenth of the energy in a litre of petrol, and that is the good news.
- How many people pedalling equals one NS200? Somewhere between 43 Tour riders and 250 tea-stall regulars.
Questions people ask
Is it bad to ride a motorcycle in a low gear at high rpm?
Not if the engine is warm, the oil is good and you stay below the rev limiter. It burns more fuel and wears parts a little faster per kilometre, but modern engines are designed for sustained high revs.
What is the top speed in first gear?
It depends on the bike's overall ratio and rev limit. On 390 Duke gearing, first gear gives about 55 km/h at 10,000 rpm; small commuters with shorter gearing often run out near 30 to 40 km/h.
Does riding in a higher gear save fuel?
Yes, as long as the engine is not labouring. Use the highest gear that lets the engine pull smoothly without knocking or juddering; lugging at very low rpm under heavy throttle is also bad for the engine.
Can I ride a bike on the Bengaluru–Mysuru Expressway?
No. NHAI banned two-wheelers and three-wheelers from the main expressway from 1 August 2023. Bikes use the service roads and the old highway.
Sources
- moto-data.net: KTM 390 Duke (2013-14) technical specifications (primary 30:80, gear teeth, final drive 15:45, 150/70-17 rear, 32 kW at 9,500 rpm)
- moto-data.net: KTM 390 Adventure (2020) technical specifications (shared primary and final drive ratios)
- Bajaj Auto: Pulsar NS200 BS VI owner's manual (2023) (49 mm stroke, shift light at 10,000-10,500 rpm)
- Holmberg K., Andersson P., Erdemir A.: Global energy consumption due to friction in passenger cars, Tribology International (2012) (one-third of fuel energy to friction)
- Holmberg K., Erdemir A.: The impact of tribology on energy use and CO2 emission globally and in combustion engine and electric cars (2019)
- US DOE Alternative Fuels Data Center: Fuel properties comparison (petrol lower heating value, about 32 MJ per litre)
- Outlook India: NHAI bans two-wheelers, autos on Bengaluru–Mysuru Expressway from August 1 (2023) (ban and 118 km length)
- HDFC Sky: Petrol and diesel prices, 23 June 2026 (Bengaluru ₹111.68 per litre)
- DriveSpark: Updated Bajaj Pulsar NS200 launched at ₹1.60 lakh (Oct 2026)
- Wikipedia: Velocette Venom (source for the March 1961 Montlhéry 24-hour record at 100.05 mph)
