Motorcycle sprocket gearing: what changing teeth does

A bigger rear sprocket multiplies torque at the wheel and costs top-gear cruising rpm. Here is the arithmetic, a calculator with a real gearbox, and why one front tooth equals about three rear teeth.

Rear hub of a 1966 Royal Enfield Crusader showing the final drive chain sprocket, drum brake arm and snail cam chain adjuster
Photo: Motacilla, CC BY 4.0, via Wikimedia Commons

A motorcycle's sprocket ratio is the rear sprocket's teeth divided by the front's: 43 ÷ 14 = 3.07 on a KTM 200 Duke. A bigger rear sprocket (or smaller front) raises that ratio, so the wheel gets more torque and the bike pulls harder in every gear, but the engine spins faster at any road speed and the gearing-limited top speed falls. A smaller rear (or bigger front) does the opposite. Gearing never adds power; it only trades acceleration against cruising rpm.

Key takeaways
  • Sprocket ratio is rear ÷ front teeth: 43 ÷ 14 = 3.07 on a KTM 200 Duke.
  • One front tooth ≈ three rear teeth: about 7% per tooth at the front against 2.5% at the rear.
  • A bigger rear means more wheel torque and higher cruising rpm, and a lower gearing-limited top speed.
  • In first gear the 200 Duke turns every newton-metre at the crank into about 28 at the axle.
  • Keep a change on a stock engine within 10%; two to three rear teeth usually fit the stock chain.
  • A 14-tooth front bends each chain link through about 26°, a 41-tooth rear under 9°.

Riders change sprockets for three reasons: punchier acceleration with a pillion and luggage, lower rpm on the highway, or because the stock size is out of stock when the chain kit is due. This post shows what a change does, using real gearbox numbers, and gives you a calculator to try your own bike.

3.07final drive ratio of a 14/43 setup (KTM 200 Duke)
about 2.5%gearing change from one rear tooth on a 40-tooth sprocket
about 7%gearing change from one front tooth on a 14-tooth sprocket
10%rule-of-thumb maximum change on a stock bike (xBhp)
The story

My 2017 Pulsar NS200, a carburetted BS4 bike with a 199.5 cc liquid-cooled single, has spent most of its life as an upright luggage tourer, with a Dominar handlebar, a tall windscreen and a tail rack, and it has done several 800–1,000 km days. Somewhere around 39,000 to 40,000 km, its drive got a Rolon brass chain kit and a 41-tooth rear sprocket from the Pulsar RS200, Bajaj's faired sibling.

That is a small hardware change with a bike-wide effect. A sprocket sits at the end of the drivetrain, so it shifts every one of the six gears by the same percentage at once: first gear, the highway gear and everything between. How big that shift is depends entirely on what the bike had before, which is exactly the arithmetic the rest of this post works through, starting with the table further down.

Sapta: Bajaj Pulsar NS200 (2017) review, around 70,000 km of touring

How does a motorcycle's gearing chain multiply torque?

Engine torque reaches the rear wheel through three reductions multiplied together:

  1. the primary drive from crank to clutch;
  2. the gearbox ratio of whichever gear you are in;
  3. the final drive of chain and sprockets.

The overall ratio is the product of the three, and wheel torque is roughly engine torque times that overall ratio, minus small friction losses.

The KTM 200 Duke is a well-documented example. Its technical data lists a primary drive of 72:22 (3.27:1), six gears from 12:34 in first to 24:22 in sixth, and a 14:43 final drive with a 520 O-ring chain.

GearGear teethGear ratioOverall ratio (× 3.27 primary × 3.07 final)Road speed at 9,000 rpm on 150/60-17
1st12:342.83328.536 km/h
2nd15:312.06720.850 km/h
3rd18:281.55615.666 km/h
4th21:261.23812.483 km/h
5th22:231.04510.599 km/h
6th24:220.9179.2113 km/h

Speeds are calculated from the ratios and the nominal tyre diameter of 611.8 mm, ignoring tyre growth and slip, so they are a little conservative at the top. The point of the table is the multiplier: in first gear every newton-metre at the crank becomes about 28 at the axle.

Three reductions, multiplied Crank Primary 72:22 = 3.27 Gearbox 2.83 (1st) to 0.92 (6th) Front 14T Rear 43T Final = 43/14 = 3.07 Overall in 6th: 3.27 × 0.92 × 3.07 = 9.2 : 1 Only the last box changes when you swap sprockets
KTM 200 Duke drivetrain ratios from its published technical data. A sprocket swap changes only the final drive, so it shifts every gear by the same percentage.

What does a bigger rear sprocket do?

A bigger rear sprocket shortens every gear by the same percentage, so the bike accelerates harder in each gear, reaches each gear's rev limit sooner, and spins faster at any cruising speed.

On xBhp's long-running World of Sprockets thread, the summary is blunt: gearing does not create power; a larger rear or smaller front favours acceleration, a smaller rear or larger front favours top speed and highway economy.

Gearing never adds power. It only trades acceleration against cruising rpm.

The size of the change is easy to work out. The percentage change in final drive equals the ratio of new to old teeth minus one:

  • One rear tooth changes gearing by about 1 ÷ (rear teeth). On a 40-tooth rear that is 2.5%.
  • One front tooth changes gearing by about 1 ÷ (front teeth). On a 14-tooth front that is about 7%, the same as roughly three rear teeth.

That is why riders who want a big change swap the front, and riders who want a small tweak swap the rear. The catch is that a smaller front sprocket makes the chain wrap more sharply, which the research below links to higher friction losses.

One tooth at each end, from 14/430% (stock 3.07)Rear +1 (44T)+2.3%, 3.14Rear +3 (46T)+7.0%, 3.29Front −1 (13T)+7.7%, 3.31Front +1 (15T)−6.7%, 2.87Right = shorter gearing (more pull). Left = taller (lower rpm).
Worked from the KTM 200 Duke's 14/43 final drive: dropping one front tooth changes the ratio about as much as adding three at the rear.
Rear sprocket and chain on a 1977 Triumph Bonneville during restoration
A rear sprocket on a 1977 Triumph Bonneville under restoration. Every tooth added here shortens all six gears by the same percentage.Photo: Makia Minich, CC BY-SA 3.0, via Wikimedia Commons

What happens when you fit a 41-tooth rear to a Pulsar NS200?

Bajaj does not list sprocket tooth counts in the NS200 owner's manual, and parts listings disagree by model year, so the honest answer depends on what your bike came with. Count the teeth on your old sprocket before ordering. Here is what a move to the RS200's 41-tooth rear does from three possible starting points, with the 14-tooth front kept:

Old rearOld ratioNew ratio (14/41)Change in gearingRpm at 100 km/h vs before
39T2.792.935.1% shorter5.1% higher
40T2.862.932.5% shorter2.5% higher
42T3.002.932.4% taller2.4% lower

Every one of those changes is within the 10% limit that xBhp's sprocket guide suggests for a stock engine. The same thread notes that a stock chain can usually absorb a change of two to three rear teeth within its adjuster range; bigger jumps need a longer or shorter chain.

Tyres move the same numbers. My NS200 now runs a 140/70 ZR17 rear (fitted May 2026); against the 130/70-17 that Bajaj lists as stock, that is about 2.3% more diameter, which partly offsets a shorter sprocket. The tyre side of that is worked out in how to read motorcycle tyre sizes.

Calculate speed and rpm for any sprocket

Enter your bike's primary ratio, the gear ratio for the gear you care about (usually top), the sprockets and the tyre. The defaults are the KTM 200 Duke in sixth gear. If your owner's manual does not list ratios, the final drive alone still tells you the percentage change, which is what matters most.

Road speed and rpm for a sprocket combination

For the KTM 390 Adventure, KTM's published data give a 15:45 final drive, which is exactly 3.00:1, with a 520 X-ring chain; the 2020 data list a 30:80 primary. Without the individual gear ratios in the public spec sheet, the calculator still shows that moving to a 47-tooth rear would shorten every gear by 4.4%, and a 16-tooth front would lengthen them by 6.7%.

Does a bigger sprocket reduce mileage?

Usually slightly, at steady highway speeds, because the engine turns more revolutions per kilometre and pays more friction and pumping loss for each. xBhp's sprocket guide says taller gearing generally helps highway mileage and shorter gearing reduces it. In the city the effect is small and can go either way, because a shorter gearing can let you use a higher gear sooner. Riding style matters more than a tooth or two.

A novel pendulum test for measuring roller chain efficiencyWragge-Morley, Yon, Lock, Alexander and Burgess (University of Bristol) · Measurement Science and Technology · 2018

To measure chain losses without the friction of a motorised rig, the team let a pendulum swing a chain drive and measured how fast its oscillations died away. The rig measures the chain's coefficient of friction to about 0.6%, which gives transmission efficiency to about 0.012%. It revealed that at very small articulation angles the chain links roll against each other instead of sliding, so losses drop sharply. The limit: low speeds and bicycle-type chains, not a 520 O-ring chain under engine torque. The lesson transfers: the smaller the angle each link bends through, the less energy the chain wastes, and bigger sprockets mean smaller angles.

Read the paper (free)
Big Sprockets and Small-Pitch Chains: Advancements in Transmissions for Olympic Track CyclingWragge-Morley, Barnaby, Burgess and Hicks · Journal of Science and Cycling · 2024

The Bristol group tested drives with the same 1:4 ratio and centre distance but differently scaled sprockets on a high-accuracy dynamometer, over 49 operating points from 70 to 130 rpm and 20 to 150 Nm. Larger sprockets measurably improved efficiency over a 97% baseline. They attribute the gain to lower chain tension, smaller articulation angles that reduce sliding friction, and less "polygon" vibration in the tight run of the chain. The limit: a two-page conference abstract on bicycle transmissions with no motorcycle data, so read it for the mechanism, not the numbers.

Read the paper (free)
How much each link bends, and chain speed ripple, by sprocket size
See the data as a table
Articulation angle per link (degrees)Chordal speed variation (% x 10)
14T25.725.1
15T24.021.9
16T22.519.2
39T9.23.2
41T8.82.9
43T8.42.7
45T8.02.4

Source: Computed from sprocket geometry: articulation angle = 360 ÷ teeth; chordal speed variation = 1 − cos(180° ÷ teeth) · Second series is multiplied by 10 to share the axis: 25.1 means 2.51%. Small front sprockets do most of the bending and cause most of the speed ripple.

The chart is why the front sprocket wears first and why going down a tooth at the front is harder on a chain than going up a tooth or three at the rear. A 14-tooth front bends each link through almost 26 degrees and makes the chain's speed ripple by about 2.5% every tooth; a 41-tooth rear bends it through under 9 degrees. Cleaning and lubrication matter more on a small front sprocket for the same reason; the routine is in how to clean, lube and adjust a chain.

Spoked motorcycle rear wheel with chrome shock absorber, drive chain running to the rear sprocket and tube-type tyre
The chain run on a spoked rear wheel. The tight upper run carries the load; the polygon effect of a small front sprocket shows up here as ripple in chain speed and tension.Photo: Paul The Writer, CC0, via Wikimedia Commons

Should you change the chain with the sprockets?

Yes. A worn chain has stretched pitch and has already worn the sprocket teeth into a matching hooked shape; putting a new chain on old sprockets, or the reverse, wears the new part quickly. That is why chains and sprockets are sold as kits, and why my NS200's 41-tooth rear went on together with a new Rolon brass chain kit. When you change tooth counts:

  1. Match the pitch. The chain size (520 on the KTM 200 Duke and 390 Adventure, for example) must match both sprockets exactly.
  2. Recount the links. More rear teeth may need more links to keep the axle within its adjuster range. A change of two to three teeth usually fits on the stock chain.
  3. Check speedometer and ABS. If speed is read from the front wheel, a sprocket swap does not affect the speedometer; if it is read from the gearbox output, the speedometer reading will shift by the same percentage as the gearing.
  4. Set slack and alignment. Use the slack figure in your owner's manual and check that the rear wheel is aligned, not just the adjuster marks.

If you are deciding between power-to-weight and gearing as a way to get more pull, the ranking in the best power-to-weight bikes under ₹4 lakh is a useful reference, and the torque side of the story is in power vs torque explained. For my own bikes and kit, see the gear page.

A grey and red Bajaj Pulsar 200NS motorcycle
A Pulsar 200NS. Count your own sprocket teeth before ordering: Bajaj's owner's manual does not list them.Photo: Sankar 1995, CC BY-SA 3.0, via Wikimedia Commons

Questions people ask

Does a bigger rear sprocket increase top speed?

No, it usually lowers the gearing-limited top speed, because the engine hits its rev limit at a lower road speed in top gear. On a small bike that cannot reach the rev limit in top gear because of air drag, a slightly shorter gear can sometimes let it pull to the same or a marginally higher speed, but that is the exception.

Is changing the front or rear sprocket better?

For a big change, the front: one tooth is worth about three at the rear. For a fine adjustment, the rear. Avoid going smaller at the front if you can, because a small front sprocket bends the chain sharply and wears it faster.

How many teeth can I change without changing the chain?

xBhp's sprocket guide puts it at two to three rear teeth on a stock chain, within the adjuster range. Beyond that, plan to change the link count, and in any case change chain and sprockets together if the chain is worn.

Will a bigger rear sprocket make the bike faster off the line?

Yes. More final drive ratio means more torque at the wheel in every gear, so the bike accelerates harder up to each gear's limit. A 2.5 to 5% change is noticeable with a pillion or luggage, but you will shift more often.

Sources

  1. moto-data.net: KTM 200 Duke (2013) technical specifications, primary, gear and final drive ratios
  2. moto-data.net: KTM 390 Adventure (2020), primary 30:80 and final 15:45 (2020)
  3. KTM: 2026 KTM 390 Adventure X technical specifications (520 X-ring chain) (2026)
  4. Bajaj Auto: Pulsar NS200 BS VI owner's manual (2023)
  5. xBhp forum: World of Sprockets (2008 to 2020)
  6. Wragge-Morley et al.: A novel pendulum test for measuring roller chain efficiency, Measurement Science and Technology (2018)
  7. Wragge-Morley et al.: Big Sprockets and Small-Pitch Chains, Journal of Science and Cycling 13(2) (2024)
  8. Wikipedia: Tire code (size to diameter)
  9. Autocar India: KTM 390 Adventure X with cruise control launched (2025)
  10. Autocar India: KTM RC 160 launched at Rs 1.85 lakh (2026)
sprocketgearingsprocket ratiofinal drivechainaccelerationtop speedPulsar NS200
Sapta

Sapta (Saptarshi Sarkar) is a mechanical engineer turned marketer in Bengaluru and a solo touring rider. He writes the seven Saptaverse blogs. Work with him or read more of RoadHook Machines.

Keep reading in RoadHook Machines

From the other blogs