What if you ran a bike on kerosene, diesel or 100% ethanol?

Kerosene and diesel would knock and smoke a petrol engine to death. Pure ethanol would barely run on petrol jetting, yet with the right fuel system it is the best of the three. The difference is octane.

Three views of a 2009 Honda CG 150 Titan Mix, the first flex-fuel motorcycle, which runs on petrol, ethanol or any mix
Photo: Moto_Honda_Flex_Titan_CG_150_Mix_Fuel_Injection_06_2009_Itu.jpg: Mariordo Mario Roberto Duran Ortiz derivative work: Mar, CC BY-SA 3.0, via Wikimedia Commons

If you ran a normal petrol bike on kerosene or diesel, it would start badly or not at all, then knock, smoke, foul its spark plug and dilute its oil, because both fuels have very low octane and evaporate poorly. On 100% ethanol, the opposite problem appears: the fuel resists knock better than petrol, but it needs about 63% more fuel per kilogram of air, so an unmodified carburettor runs dangerously lean. Of the three, only ethanol makes a good motorcycle fuel, and only in an engine built for it; India now sells flex-fuel bikes that take up to E85.

Key takeaways
  • Octane decides it: ethanol rates 108.6 RON, petrol about 91, diesel only 15 to 25, kerosene near zero.
  • An 11:1 engine heats its charge to about 429 °C, roughly 200 °C past diesel's autoignition point, so diesel and kerosene knock.
  • Ethanol needs 63% more fuel per kg of air; on petrol jetting it runs at a lean lambda of about 1.47.
  • A litre of ethanol holds 67% of petrol's energy, so expect about a third fewer km per litre.
  • India's first flex-fuel bikes (2026) run E20 to E85; none is rated for E100.

Each fuel fails for a different chemical reason, and each reason is a number you can look up: octane, cetane, flash point, energy content and air-fuel ratio.

This post works through them for a typical Indian single with an 11:1 compression ratio, the NS200's figure, and shows the arithmetic.

The story

On the night of 19 November 2005, Shanmugam Manjunath, a 27-year-old Indian Oil Corporation sales officer and IIM Lucknow graduate, went to a petrol pump in Lakhimpur Kheri, Uttar Pradesh, to collect samples of petrol allegedly being sold adulterated. He had earlier ordered two pumps in the district sealed for selling adulterated fuel, and one had reopened. He was shot dead; his body was found the next day in his own car.

A sessions court convicted all eight accused, including the pump owner, in 2007, and the Supreme Court upheld life sentences for six in March 2015. Fuel that is not what the pump says it is was worth killing over, which is a measure of how much money hides in the gap between petrol and cheaper liquids.

India TV News (PTI): SC sentences six convicts to life imprisonment in Manjunath case
108.6research octane number of ethanol
15 to 25octane number of diesel
67%energy per litre of E100 against petrol (US DOE)
E20 to E85range of India's first 100 cc flex-fuel bikes (Hero, 2026)

What makes a fuel suit a petrol engine?

A spark-ignition engine needs a fuel that evaporates easily, mixes with air, and does not ignite on its own when squeezed. A diesel engine needs the opposite: a fuel that ignites quickly from the heat of compression alone.

  • Octane measures resistance to self-ignition: high is good in a petrol engine.
  • Cetane measures readiness for it: high is good in a diesel engine.

They pull in opposite directions, which is why no single liquid is good in both engines. The properties are split into two tables so they read on a phone.

Ignition properties

FuelOctane (RON)Flash pointAutoignition
Petrol (E10)91 to 92 (regular)−43 °C247 to 280 °C
Diesel15 to 25above 52 °C210 °C
Kerosene (paraffin)Near 0 (TVO, a doped kerosene: 55 to 70)above 38 °C210 °C (Jet A-1)
Ethanol (E100)108.6about 13 °C365 °C

Energy and mixture properties

FuelEnergy (LHV)Stoich. air-fuel ratioCetane
Petrol (E10)31.3 to 32.4 MJ/l14.7:1Not rated
Diesel35.8 MJ/lNot used with a carburettor40 to 55
Kerosene (paraffin)43.0 MJ/kgNot in my sourcesNot in my sources
Ethanol (E100)21.3 MJ/l9.0:1Not used as a diesel fuel
Knock resistance (RON)050100Kerosene ~0Diesel15 to 25TVO 55 to 70(tractors, 4.5:1)Petrol 91Ethanol108.6Higher is better in a spark-ignition engine
The octane numbers from the table on one line. Everything left of petrol knocks in an 11:1 engine; ethanol sits comfortably to its right.

Petrol octane, diesel octane and ethanol octane are from the reference tables on Wikipedia's octane article; cetane, energy per litre and ethanol's flash point from the US Department of Energy's Alternative Fuels Data Center comparison chart (converted from Btu per gallon); kerosene energy per kilogram from Wikipedia's heat-of-combustion tables; air-fuel ratios from the International Energy Agency's Advanced Motor Fuels programme.

Energy in one litre of fuel (lower heating value)
See the data as a table
Energy per litre (MJ/l)
Petrol (E10)31.8
Diesel35.8
Ethanol (E100)21.3

Source: US DOE Alternative Fuels Data Center, Fuel Properties Comparison · Converted from Btu per US gallon (1 Btu/gal = 0.2787 kJ/l). Petrol is the midpoint of the 112,114 to 116,090 Btu/gal range.

What happens if you put diesel in a petrol bike?

It would probably not start, and if it ran on the petrol left in the carburettor or rail, it would knock and smoke as the diesel arrived. Diesel's flash point is above 52 °C, so at room temperature it barely gives off vapour; a carburettor or port injector relies on fuel evaporating in the intake. Most of the diesel would enter the cylinder as droplets, wet the spark plug and the cylinder wall, and drain past the rings into the oil.

The part that does burn burns badly, because diesel is designed to self-ignite. A simple estimate shows why. Compressing air adiabatically raises its temperature by:

\[ T_2 = T_1 \, r^{\,\gamma - 1} = 303\ \text{K} \times 11^{0.35} \approx 702\ \text{K} \approx 429\ ^\circ\text{C} \]

That uses a 30 °C intake charge, a ratio of specific heats of about 1.35 for an air-fuel mixture, and the NS200's 11:1 compression ratio from Bajaj's manual.

The end of compression is roughly 200 °C hotter than diesel's 210 °C autoignition temperature, and diesel's low octane (15 to 25) means it does not wait long at that heat. Pockets of mixture explode before the flame from the spark reaches them. That is knock: a sharp pressure spike that hammers the piston crown and rings. Petrol survives the same compression because its octane holds off self-ignition long enough for the flame to sweep the chamber.

How hot the squeeze gets (11:1)Compressed charge: about 429 °C210210247-280365DieselKerosenePetrolEthanol
Autoignition temperatures in °C against the adiabatic estimate above. All four sit below 429 °C, so it is octane, the delay before self-ignition, that decides whether the spark's flame gets there first.

The reverse experiment has been done properly, in a diesel engine. Royal Enfield sold a Bullet with a 325 cc diesel engine, known as the Taurus, from the late 1980s until about 2000. RideApart's account gives it 6.5 hp, 11 lb-ft (about 15 Nm), a top speed near 64 km/h and claimed economy of up to 90 km/l, and says it ended because it could not meet India's tightening emission standards by 2000. A diesel motorcycle works. A petrol motorcycle fed diesel does not.

What happens if you run a petrol bike on kerosene?

Kerosene sits chemically between petrol and diesel and fails in the same two ways, slightly less violently: it does not evaporate well (flash point above 38 °C) and it has almost no knock resistance. Farm tractors once ran on it, and the way they did it explains the problem.

Tractor vaporising oil (TVO), a kerosene with added aromatics to raise its octane to roughly 55 to 70, powered British and Australian tractors after the Second World War. TVO tractors worked around the problem in three ways:

  • they started on petrol from a small tank and switched to TVO only once hot;
  • they used exhaust heat to vaporise the fuel in the inlet manifold;
  • they ran a much lower compression ratio.

Engines started on a small petrol tank and switched to TVO only once hot, used exhaust heat to vaporise the fuel in the inlet manifold, and ran a much lower compression ratio: the TVO Ferguson TE20 used 4.5:1 against 5.77:1 for the petrol version. A modern motorcycle at 11 to 12.6:1 is more than twice the TVO engine's ratio, with plain kerosene instead of doped TVO.

Analysis of the Influence of Gasoline Adulteration on Lubricant Degradation and Internal Combustion Engine PerformanceGonçalves, Ferreira, Preto, Karmouche, Chavarette and Outa · ACS Omega 7(38) · 2022

Researchers at UNESP and UniRV in Brazil ran a 163 cc single-cylinder four-stroke (a Honda GX-type engine, rated 5.5 cv at 3,600 rpm) at a fixed speed near 2,000 rpm, driving an alternator, on clean petrol and on petrol with 5, 10, 15 or 20% of ethanol, kerosene or thinner. Each condition ran 40 hours, which they equate to about 2,000 km, with oil analysis after each.

Kerosene caused hesitation and speed oscillations that grew with concentration, power loss and higher consumption; 20% thinner made the engine fail repeatedly. All contaminants left heavier-than-normal carbon on the spark plug, while ethanol raised engine speed and was the least harmful to the oil.

The limit you should know: one engine, one load, mostly single runs, and most of the numbers only appear in figures, so it shows the direction of the damage rather than its size.

Read the paper (free)
A diesel motorcycle works. A petrol motorcycle fed diesel does not.The working above

That small engine is a fair stand-in for a commuter motorcycle: air-cooled, single-cylinder, carburetted. Its results map onto the chemistry in the table. Kerosene does not vaporise fully, so some of it passes unburnt into the oil and some leaves as soot on the plug; what does ignite knocks. A bike on pure kerosene would be worse than the 20% blend in every respect.

A single-burner wick kerosene stove, the kind long used in Indian kitchens
Kerosene's natural home is a wick stove, where it burns slowly at atmospheric pressure. Inside a high-compression engine, the same fuel explodes at the wrong moment.Photo: Unknown, CC BY-SA 4.0, via Wikimedia Commons

What happens if you fill a normal bike with 100% ethanol?

It runs lean, hesitates and overheats, and on an old bike the fuel may also swell or harden rubber parts. Ethanol carries oxygen in every molecule, so it needs only 9.0 kg of air per kg of fuel, against petrol's 14.7. A carburettor meters fuel by jet size and does not know which fuel it is passing. If a bike is set slightly rich on petrol at 13.2:1, the same jetting on ethanol gives:

\[ \lambda = \frac{AFR_{actual}}{AFR_{stoich}} = \frac{13.2}{9.0} \approx 1.47 \]

A lambda of 1.47 is 47% more air than the fuel can use, far leaner than any production engine is calibrated to run under load. To restore the original mixture, the jets must pass 14.7 / 9.0 = 1.63 times as much fuel by mass. Since ethanol's density is close to petrol's, the jet area must grow about 63%, and its diameter by the square root of that:

\[ \frac{d_{new}}{d_{old}} = \sqrt{1.63} \approx 1.28 \]

A 28% bigger main jet, and similar changes to the pilot circuit. A fuel-injected bike's ECU can add fuel through its oxygen sensor, but only within its trim range, which on a petrol calibration is far short of 63%. And because ethanol holds 67% of petrol's energy per litre, the same bike would also cover about a third fewer kilometres per litre at equal efficiency. My earlier post on what E20 does to motorcycle engines works through the same logic at 20%.

Ethanol blends: range and break-even price

That last output is why flex-fuel bikes live or die on price. The NITI Aayog expert committee's 2021 roadmap recorded the industry's view that E100 vehicles make sense only if E100 sells at about 30% below petrol and is available across the country, which is the energy gap in rupees.

Roadmap for Ethanol Blending in India 2020-25: Report of the Expert CommitteeNITI Aayog and Ministry of Petroleum and Natural Gas · Government of India · 2021

The committee set out India's path to E20 and assessed flex-fuel and E100 vehicles. In vehicle tests it summarised, E20 cut carbon monoxide by 50% in two-wheelers (30% in four-wheelers) and hydrocarbons by 20% against neat petrol, while NOx in two-wheelers rose about 10% and acetaldehyde rose with both blends.

It recorded industry estimates that a flex-fuel two-wheeler would cost ₹5,000 to ₹12,000 more than a petrol one, and that E85 had been notified for two-wheelers in 2016. SIAM did not recommend pursuing E100 vehicles until E100 was cheap and available nationwide. The limit you should know: the E10 and E20 emission tests were run years apart on different vehicles, and the cost figures are industry estimates, not audited data.

Read the report (free)

How is a flex-fuel motorcycle different?

A flex-fuel bike measures what is in the tank, through its oxygen sensor or a fuel sensor, and adjusts injection quantity and ignition timing to suit, with seals, hoses and pump materials chosen to tolerate ethanol. Brazil proved it at scale. Honda launched the first flex-fuel motorcycle there, the CG 150 Titan Mix, in March 2009; by December 2012 Honda and Yamaha had built 2,291,072 flex motorcycles across five models, 48.2% of Brazil's motorcycle output that year, running on hydrous ethanol or on petrol blended with about 25% ethanol.

A 2013 Honda Biz 125 Flex step-through motorcycle in Brazil with its flex-fuel badge
The Honda Biz 125 Flex, one of five Brazilian flex-fuel models on sale by 2012. In Brazil, choosing ethanol or petrol at the pump is an everyday price decision.Photo: Mariordo (Mario Roberto Durán Ortiz), CC BY-SA 3.0, via Wikimedia Commons

India's flex-fuel bikes, 2026

India arrived in 2026:

  • Hero Splendor+ and HF Deluxe flex (June 2026): ₹82,710 and ₹72,792 ex-showroom in Delhi, rated for E20 to E85 with a revised ECU calibration, a new fuel pump and a secondary fuel filter; on E85 the 97.2 cc engine makes 8.6 hp at 8,000 rpm.
  • Yamaha FZ Blue Flex (July 2026): 149 cc, ₹1.24 lakh.
  • Honda ADV 160 (July 2026): India's first E85-compatible scooter.

None of these is rated for E100. The engineering reason is the cold start. Ethanol needs more heat to evaporate than petrol, and the IEA's Advanced Motor Fuels programme puts the starting limit of neat ethanol at around 12 °C; at least 15% petrol in the mix solves it. E85 is that fix, written into a fuel name.

So which of the three would get you furthest?

On an unmodified bike: none, safely. On a bike built for it: ethanol by a wide margin, though each litre takes you about a third less far. Here is the scorecard for a standard 11:1 petrol single.

Fuel in a standard petrol bikeStarts?Main failureEngine survives?
DieselRarely, unless petrol is still in the systemPoor vaporisation, knock, oil dilution, plug foulingNot for long under load
KerosenePoorly, and only when hotKnock, soot, unburnt fuel in the oilDamaged; tractors needed 4.5:1 compression and doped TVO
100% ethanolHard when coldVery lean mixture (lambda about 1.47), heat, seal attack on older bikesPossibly briefly; risky at speed
E85 in a flex-fuel bikeYesAbout 25% fewer km per litre than on E10Yes; designed for it

For how injection and carburettors handle fuel and altitude differently, see fuel injection vs carburettor; for whether higher-octane petrol is worth paying for, premium petrol for bikes. India's own story of why fuel prices and taxes look the way they do is a question for the Kyun world.

Verdict: possible with changes, and only for ethanol

Diesel and kerosene fail in a petrol engine on octane: an 11:1 squeeze heats the charge to about 429 °C, and fuels rated 0 to 25 RON self-ignite before the flame arrives, while their poor evaporation washes fuel into the oil. Pure ethanol has the opposite profile, 108.6 RON, but needs 63% more fuel per kilogram of air and struggles to start below about 12 °C. Give it bigger jets or an ECU that can add that fuel, alcohol-proof seals and some petrol for cold starts, and you have the E85 flex-fuel bikes already on sale in India.

What if next?

Questions people ask

What happens if I accidentally put diesel in my bike?

Do not start it, or switch off at once if you already have. Drain the tank and fuel lines, clean or replace the fuel filter, and if the engine ran, change the oil and spark plug because diesel washes into the crankcase and fouls the plug. A small amount mixed into a nearly full tank of petrol may run roughly, but it should still be drained.

Can a bike run on kerosene mixed with petrol?

It can run, badly, and it is damaging. Tests on a small single found kerosene blends of 5 to 20% caused hesitation, power loss, higher consumption and heavy spark plug carbon.

Can I use E85 or E100 in my normal bike?

Not unless the manufacturer rates it for that fuel. Most bikes sold in India since 2023 are designed for E20. Higher blends need a flex-fuel calibration and ethanol-proof materials; India's flex-fuel bikes, such as Hero's flex Splendor+, are rated up to E85.

Is there an E100 standard in India?

E100 has a national standard, IS 15464, and India notified E85 for two-wheelers in 2016, but no mainstream motorcycle on sale in 2026 is rated for E100. Flex-fuel bikes launched in 2026 stop at E85.

Sources

  1. Gonçalves et al.: Analysis of the Influence of Gasoline Adulteration on Lubricant Degradation and Internal Combustion Engine Performance, ACS Omega (2022)
  2. NITI Aayog and MoPNG: Roadmap for Ethanol Blending in India 2020-25 (2021)
  3. US DOE Alternative Fuels Data Center: Fuel Properties Comparison
  4. IEA Advanced Motor Fuels: Ethanol fuel properties
  5. Wikipedia: Octane rating (fuel octane tables)
  6. Wikipedia: Autoignition temperature
  7. Wikipedia: Flash point
  8. Wikipedia: Heat of combustion
  9. Wikipedia: Tractor vaporising oil
  10. Wikipedia: Flexible-fuel vehicle (Brazilian flex motorcycles)
  11. Bajaj Auto: Pulsar NS200 owner's manual (compression ratio)
  12. RideApart: Remembering Royal Enfield's diesel-powered Bullet (2021)
  13. Autocar India: Hero launches flex-fuel Splendor+ and HF Deluxe (2026)
  14. Business Today: India's first flex-fuel scooter launched (2026)
  15. 91Wheels: Yamaha FZ Blue Flex launched at Rs 1.24 lakh (2026)
  16. India TV News (PTI): SC sentences six convicts to life imprisonment in Manjunath case (2015) (source for the story)
  17. Wikipedia: Manjunath Shanmugam (background to the story: the earlier sealing of two pumps, trial dates)
kerosene in petroldiesel in petrol engineE100flex fuel motorcycleoctanecetaneethanolE85fuel adulteration
Sapta

Sapta (Saptarshi Sarkar) is a mechanical engineer turned marketer in Bengaluru and a solo touring rider. He writes the seven Saptaverse blogs. Work with him or read more of RoadHook Machines.

Keep reading in RoadHook Machines

From the other blogs