Does your old bike need an additive for E20 petrol?

A bottle cannot put back the 3.4% of energy E20 takes out of a litre, or swap a rubber hose. What additives can do, what they cannot, and what to check on a pre-2020 bike instead.

An HP petrol pump on a highway at Addakal in Telangana
Photo: Chanduclicks, CC BY-SA 4.0, via Wikimedia Commons

Most old bikes do not need an E20 fuel additive, and no additive can fix the two real effects of E20. A bottle cannot put back the roughly 3.4% of energy per litre lost going from E10 to E20, and it cannot change a rubber hose or seal that ethanol swells. What does help on a pre-2020 or carburetted bike is cheaper: inspect fuel hoses and seals, have the carburettor checked for a lean mixture, ride the bike regularly, and keep the tank full if it will stand. Additives earn their place only for storage and deposit cleaning.

Key takeaways
  • E20 carries about 3.4% less energy per litre than E10; that gap is chemistry.
  • A typical additive dose is about 0.4% of the fuel, so it cannot refill the gap.
  • The best lab result, a purpose-made package, cut the E20 loss from 4.94% to 3.36%.
  • ARAI found NBR-PVC, ECO rubber and PA66 nylon degrade faster in E20; metals did not.
  • On a carburetted bike, check hoses, seals and mixture, not the additive shelf.
  • Only 100-octane petrol is ethanol-free in India; XP95 is E20.

Since 1 April 2026 there is no regular alternative: the Ministry of Petroleum and Natural Gas ordered E20 petrol at a minimum 95 RON at every pump in every state, so owners of older bikes ask whether a bottle from the counter will protect them.

The question is not new. In 2014, years before E20, an xBhp member asked which additive to use for his Unicorn Dazzler because dirty fuel gave it hiccups; one reply said additives were pointless in Indian conditions and the fix was a better pump and a clean carburettor. The chemistry of E20 makes that answer more right, not less.

3.4%less energy per litre in E20 than E10 (from US DOE fuel data)
0.4%of the fuel volume that a typical additive dose makes up
BS4 (2017)Bajaj says its bikes are E20 material-compliant back to here
1 Apr 2026E20 with 95 RON minimum mandated nationwide

What does E20 actually change in an old engine?

E20 changes three things in an engine designed for E0 or E10: energy per litre, the air-fuel ratio the fuel needs, and how the fuel treats certain plastics, rubbers and water. Octane goes up too, but older Indian bikes have compression ratios around 9.5-10:1 and gain nothing from that; see why premium petrol rarely helps.

The story

On 1 September 2025, the worry reached the Supreme Court. Advocate Akshay Malhotra had filed a public interest petition asking for ethanol-free petrol to stay on sale for vehicles built before April 2023, for pumps to be labelled, and for a national study of E20 on older vehicles. His counsel, Senior Advocate Shadan Farasat, said the petitioner did not oppose blending, cited NITI Aayog's 2021 roadmap on older vehicles, and pointed to reported mileage drops of about 6%.

Attorney General R. Venkataramani replied that the policy had been framed after considering all aspects, and that it helped sugarcane farmers and saved foreign exchange. The bench of Chief Justice B. R. Gavai and Justice K. Vinod Chandran dismissed the petition at once, LiveLaw reported, without detailed reasons. For owners of old bikes, that settled one thing: E20 is the fuel, so the question is what to do about it.

LiveLaw: Supreme Court dismisses PIL challenging E20 petrol policy (Sep 2025)

Energy. The US Department of Energy puts a gallon of ethanol at 67% of the energy of a gallon of gasoline. Blend 20% of it in and the litre carries about 93.4% of pure petrol's energy, against 96.7% for E10. That gap from E10 to E20, 3.3 points or 3.4% of E10's energy, is set by chemistry, not by refining quality.

Calculated in this post from the DOE figure that ethanol carries 67% of petrol's energy per gallon (US DOE): E10 is 0.9 × 100 + 0.1 × 67 = 96.7%, E20 is 0.8 × 100 + 0.2 × 67 = 93.4%, and 3.3 ÷ 96.7 ≈ 3.4%.

The Ministry of Petroleum has quoted a 1-6% efficiency drop with E20, and Autocar India reported real-world drops of 3-20% depending on vehicle age and riding.

Mixture. Ethanol (C2H5OH) is about 35% oxygen by mass, so each kilogram needs less air to burn completely than petrol does.

Calculated in this post from the formula C₂H₆O and molar mass of 46.069 g/mol (Wikipedia: Ethanol): one oxygen atom of about 16 g/mol is 16 ÷ 46.07 ≈ 35% of the mass.

A fuel-injected bike with an oxygen sensor sees the leaner exhaust and adds fuel. A carburettor cannot: it meters fuel through fixed jets, so on E20 it runs leaner than it was set up for. Autocar's explainer notes that a pre-BS4 carburetted bike can be rejetted to run properly on E20, at some cost in efficiency.

Side view of an air-cooled motorcycle engine showing cooling fins, carburettor and crankcase
On a carburetted engine the fuel is metered by fixed jets. Run E20 through jets sized for E5 or E10 and the mixture goes lean, because ethanol brings its own oxygen.Photo: Paul The Writer, CC0, via Wikimedia Commons

Materials and water. Ethanol mixes with water and is a polar solvent, so it attacks some elastomers and plastics that petrol leaves alone, and a tank of E20 left standing can pull in moisture. Which materials suffer is a measured fact, not a guess; ARAI tested them.

Energy per litre relative to ethanol-free petrol
See the data as a table
Energy (%)
E0100
E1096.7
E2093.4
E27 (Brazil)91.1
E10067

Source: Calculated from US DOE Alternative Fuels Data Center: E100 has 67% of the energy of gasoline per gallon · Linear blend of volumes. Real engines can win back part of the loss through higher octane and charge cooling, mainly with recalibration.

Impact of 20% ethanol-blended gasoline (E20) on metals and non-metals used in fuel-system components of vehiclesMoqtik A. Bawase and Sukrut S. Thipse · ARAI Journal of Mobility Technology · 2021

ARAI immersed 8 metals, 6 elastomers and 4 plastics used in fuel systems in E20 and in BS4 commercial petrol, following SAE J1747 and J1748, and measured corrosion rates for metals and mass, volume, tensile strength, elongation, impact strength and hardness for the rest. E20's effect on the metals was insignificant. Polychloroprene, SBR, HNBR and fluoroelastomer (FKM) did as well or better in E20. NBR-PVC and epichlorohydrin (ECO) rubbers and PA66 nylon degraded more in E20 than in petrol, especially in tensile strength and volume change. The limit: laboratory immersion, not a road fleet, and the parts in your bike depend on its maker and year.

Read the paper (free)

What can an additive do, and what can it not?

An additive can clean, protect and stabilise; it cannot add meaningful energy or change what a part is made of. A typical dose is tiny. Liqui Moly sells its E20 Additive as a 150 ml can for 40 litres of fuel, which is 0.375% of the volume.

Calculated in this post from the pack size on Liqui Moly's page: 150 ml ÷ 40,000 ml = 0.375%.

Even if that liquid carried as much energy as petrol, it could restore at most about 0.4% of the litre's energy, about a ninth of the 3.4% that E20 removes. The product page makes only qualitative claims:

  • smoother running and better acceleration;
  • protection against water and corrosion;
  • cleaner injectors.

It quotes no mileage figure.

What an additive bottle is up against (per litre)Energy E20 removes vs E10Most a 0.4% dose could addBest lab recovery (Saroj 2024)3.4%0.4%, if it burned like petrolabout 1.6 points of a 4.94% loss
Scale drawing of the energy arithmetic. Even a purpose-built additive package in the lab left most of the E20 loss in place; a shop bottle at 0.4% of the fuel cannot close the gap.
E20 effectCan an additive fix it?What actually fixes it
3.4% less energy per litre than E10No. A 0.4% dose cannot replace itNothing on an old bike; E20-calibrated engines recover part of it
Lean running on a carburettorNoCarburettor check: air-fuel screw, or rejetting for E20
Swelling or cracking of NBR-PVC and ECO rubber, PA66 partsNoReplace hoses, seals and O-rings with ethanol-rated parts (FKM, HNBR)
Water pulled into fuel in a standing bikePartly: corrosion inhibitors and stabilisers helpRide regularly; keep the tank full; drain the float bowl for long storage
Tank and fuel-system rustPartlyCheck the tank at services, as Autocar advises; fix the rust
Injector and valve depositsYes, detergents helpEthanol already dissolves some deposits; occasional dose is enough
Performance evaluation of high octane gasoline fuel(s) on high compression ratio (HCR) motorcycle, based on chassis dynamometer testShyamsher Saroj et al. · SAE Technical Paper 2024-01-2375 · 2024

An Indian team ran a high-compression motorcycle on a chassis dynamometer over the Indian Driving Cycle with neat petrol, E10 and E20, with and without a gasoline multifunctional additive and an octane booster. Adding ethanol alone cut fuel economy by 1.9% at E10 and 4.94% at E20, and reduced wide-open-throttle power. Doping the blends with the additive package trimmed the economy loss to 0.74% at E10 and 3.36% at E20. The limit: a purpose-developed additive at research dose on one high-compression bike, not an off-the-shelf bottle on a carburetted commuter. Even here, most of the E20 loss remained.

Read the abstract (free)
The strongest case for additives I found still leaves two-thirds of the E20 penalty in place.

That is the strongest case for additives I found, and it still leaves two-thirds of the E20 penalty in place. Autocar India asked manufacturers about it in September 2025 and reported that none of them saw additives or stabilisers as a fix for E20 issues, adding that there is not enough long-term data either way.

Additive cost vs the energy E20 takes away

Which old bikes are actually at risk?

The bikes at most risk are pre-2017 carburetted models and anything built before 2005, by the manufacturers' own statements. Here is what each major maker has said publicly.

MakerWhat it says about E20Reported by
Bajaj (incl. KTM and Triumph it builds)All motorcycles made in the last 10 years are E20 compatible; warranty still applies on E20; slight mileage dip possible. Earlier statement: material-compliant back to BS4 (2017)Rushlane, Jul 2026; Autocar India, Sep 2025
Royal EnfieldWhole range E20-compliant since BS6 (2020); developing upgrade kits for older bikesAutocar India, Sep 2025
Hero MotoCorpE20-compliant production from April 2023; pre-2023 BS3/BS4 bikes may see a marginal efficiency lossAutocar India, Sep 2025
HondaFully E20-ready from April 2025; older models material-compatibleAutocar India, Sep 2025
TVSE20 material-compliant since 2023Autocar India, Sep 2025
Government (MoRTH)Only some older BS3 petrol vehicles (2005-2016) may need a few rubber parts replaced at serviceBikeDekho, Jul 2026
A fuel pump in Brazil dispensing alcohol (ethanol) fuel
Brazil has sold high-ethanol fuel for decades. Bajaj cites its exports there, where standard petrol carries 27% ethanol, as evidence its engines cope with E20.Photo: Unknown, CC BY-SA 2.0, via Wikimedia Commons

The government's line in a July 2026 Rajya Sabha reply was that concerns had "mainly been circulating on social media". An Autocar India report the same month noted that the Ministry of Heavy Industries cited ARAI trials of 20,000 km on two-wheelers with no significant adverse effect on engine performance.

Meanwhile ARAI's own materials study shows specific rubbers and plastics do degrade faster in E20. Both can be true: an engine can run fine for 20,000 km while a 15-year-old fuel hose quietly hardens.

What should I check on a pre-2020 bike instead?

Start with the rubber and the mixture. The drawing shows where the at-risk parts sit on a typical carburetted bike.

Fuel tank: check for rust1. Petcock seals2. Fuel hose (NBR blends)3. Float-bowl gasket and O-rings4. Intake rubber: air leaksto engineDots: rubber parts to inspect; ethanol-rated parts use FKM or HNBR
Where E20 bites on an older carburetted bike: the rubber in the petcock, hose, float bowl and intake, and the jets that now meter a leaner mixture.
  1. Fuel hoses and clamps. Look and feel along the tank-to-carb or tank-to-injector hose for cracking, swelling, stickiness or seepage. Replace with hose rated for ethanol blends.
  2. Petcock, float-bowl gasket and O-rings. These are the hidden rubber parts most likely to be NBR blends on older bikes. A weeping float bowl or a petcock that drips when off is the sign.
  3. Carburettor mixture. If the bike hesitates, pops on the overrun or idles unevenly after the switch to E20, have a mechanic check the air-fuel screw and, if needed, jetting. My 2017 BS4 NS200 is carburetted and runs its air-fuel screw at about 2.8 turns out, a setting worth recording before anyone touches it.
  4. Fuel tank. Check for rust at every service, as Autocar advises; rust flakes block filters and injectors.
  5. Riding pattern. Ride the bike at least weekly. If it will stand for weeks, fill the tank to the top to limit air space and condensation, and for months, drain the carburettor float bowl.
  6. Storage dose. For a bike parked for a season, a stabiliser is sensible. KTM's own manual recommends a fuel stabiliser for storage and suggests filling with the lowest-ethanol fuel available.
Sapta's Pulsar NS200 on a snowy mountain road in Sikkim
My 2017 Pulsar NS200 is a carburetted BS4 bike, inside the window Bajaj calls material-compliant. Hoses and carb setting are what I would check, not the label on an additive.Photo: Sapta

For the full engineering of how E20 affects fuelling, mileage and parts, read what E20 petrol does to a motorcycle engine. Carburetted and fuel-injected bikes react very differently, as explained in fuel injection vs carburettor. If you are buying an older bike now, add hose and carb checks to the used bike buying checklist, and plan longer trips with the extra margin in motorcycle fuel range planning.

Questions people ask

Will an additive give my old bike its mileage back?

Not fully. The energy gap from E10 to E20 is about 3.4%, and an additive is about 0.4% of the fuel. The best research result, with a purpose-made additive and octane booster, recovered about a third of the E20 loss on one motorcycle.

Is my BS4 bike safe on E20?

Bajaj says its bikes are material-compliant back to BS4, Royal Enfield's range is compliant from BS6, and Hero and TVS from 2023. For a BS4 bike from another maker, inspect rubber fuel parts at the next service and watch for leaks or poor running.

Should I add an additive at every fill?

There is no manufacturer-backed case for it on a bike that is ridden regularly. An occasional detergent dose, or a stabiliser before storage, covers what additives can actually do.

Can I avoid E20 by filling premium?

No. IndianOil's XP95 is E20, and Autocar measured 19.88% ethanol in its sample. Only 100-octane grades are ethanol-free in India.

My carburetted bike stalls more on E20. Why?

Most likely a lean mixture: ethanol's oxygen content means fixed jets now deliver less fuel than the engine wants. A mechanic can richen the idle circuit or rejet. Check for an air leak at the intake rubber too, since old rubber is also the part E20 stresses.

Worried about monsoon water in an E20 tank instead? I worked that out separately, with a 12 L tank: E20 petrol and monsoon water.

Sources

  1. Bawase and Thipse: Impact of E20 on metals and non-metals used in fuel-system components, ARAI Journal of Mobility Technology (2021)
  2. Saroj et al.: Performance evaluation of high octane gasoline fuels on a high compression ratio motorcycle, SAE Technical Paper (2024)
  3. US Department of Energy, Alternative Fuels Data Center: Fuel properties comparison
  4. Autocar India: How E20 petrol affects your bike and scooter, explained (2025)
  5. Autocar India: E20 could damage rubber parts in fuel systems of E10 vehicles, ARAI (2026)
  6. Autocar India: How much ethanol is in your petrol? (2025)
  7. BikeDekho: E20 petrol may need rubber part changes in BS3 vehicles, says MoRTH minister (2026)
  8. Rushlane: Bajaj confirms E20 compatibility across range (2026)
  9. Autocar Professional: Govt mandates nationwide sale of E20 petrol with minimum RON 95 (2026)
  10. PRS India: Summary of NITI Aayog's Roadmap for Ethanol Blending in India 2020-25 (2021)
  11. LiveLaw: Supreme Court dismisses PIL challenging E20 petrol policy (2025) (source for the Malhotra petition and its dismissal)
  12. Liqui Moly: E20 Additive product page, dose and claims
  13. KTM: 2024 390 Duke owner's manual (EU), fuel and storage (2023)
  14. Sunday Guardian: Fuel prices on 5 April 2026, including XP100 (2026)
  15. xBhp: Which fuel additive to use for a 4-stroke bike (forum thread) (2014)
E20ethanolfuel additivecarburettorBS4fuel hoseARAI
Sapta

Sapta (Saptarshi Sarkar) is a mechanical engineer turned marketer in Bengaluru and a solo touring rider. He writes the seven Saptaverse blogs. Work with him or read more of RoadHook Machines.

Keep reading in RoadHook Machines

From the other blogs